Hi guy I'm having problems with the control of servos for the elevation and recoil. the recoil will work once or twice and then it goes in and stays in and the elevation works intermittently or not at all.
I have phoned Tankzone and emailed them twice but no answer as of yet. So any help please.
Adrian
Clark TK24 problems.
Clark TK24 problems.
The South will rise again.
That's South Wales mun Boyo.
.U.K.
That's South Wales mun Boyo.
.U.K.
-
AlwynTurner
- 2nd Lieutenant
- Posts: 2654
- Joined: Thu Oct 23, 2014 10:47 am
- Location: Chapel-en-le-Frith, Derbyshire
Re: Clark TK24 problems.
Hi gisalook, this is probably a stupid question but have you checked the state of the battery and made sure all the connections were solid? I have had funnies with my tanks and suddenly realised that it was a while since I charged it. Doh.....
Alwyn
Alwyn
YOU'RE NEVER TOO OLD TO HAVE A HAPPY CHILDHOOD!
Saladin scratchbuild, Matilda scratchbuild, Churchill scratchbuild, Crusader scratchbuild, M10 Achiĺles scratchbuild, Universal Carrier scratchbuild
Saladin scratchbuild, Matilda scratchbuild, Churchill scratchbuild, Crusader scratchbuild, M10 Achiĺles scratchbuild, Universal Carrier scratchbuild
Re: Clark TK24 problems.
Thanks Alwyn yes that's the first thing I checked.
The South will rise again.
That's South Wales mun Boyo.
.U.K.
That's South Wales mun Boyo.
.U.K.
-
c.rainford73
- Major
- Posts: 6104
- Joined: Thu Aug 25, 2016 7:34 pm
- Location: Connecticut USA
Re: Clark TK24 problems.
Hi there. What radio and Tx are you using? I had a heck of a time once with a Clark board trying to do this without two of the radio signal servos reversed and it wouldn't work properly. I have had the best luck using flysky and or hobby King radios.gisalook wrote:Hi guy I'm having problems with the control of servos for the elevation and recoil. the recoil will work once or twice and then it goes in and stays in and the elevation works intermittently or not at all.
I have phoned Tankzone and emailed them twice but no answer as of yet. So any help please.
Adrian
Mr Maxmekker might be able to help you if you reach out to him. For my king tiger tank with the tk24 installed I used an inexpensive 6ch flysky radio. What order are four transmitter and receiver channels in vs the Clark board? Send some pictures
Tanks alot.... 
-
c.rainford73
- Major
- Posts: 6104
- Joined: Thu Aug 25, 2016 7:34 pm
- Location: Connecticut USA
Re: Clark TK24 problems.
I was able to achieve this without reprogramming the board with the remote control. Where are your servos plugged into respectively?
Tanks alot....
Re: Clark TK24 problems.
do you have chanche to test the servo 'ports' on the Board With another servo , 'one by one ' ? ( if not allready done )
Drammen Rock City
-
AlwynTurner
- 2nd Lieutenant
- Posts: 2654
- Joined: Thu Oct 23, 2014 10:47 am
- Location: Chapel-en-le-Frith, Derbyshire
Re: Clark TK24 problems.
One way I tested my servos was to plug them directly into the receiver (port 1 or 2) to test the servo function - you will have to power the receiver if unplugged from the MFU. Sorry if I'm teaching my grannie to suck eggs!!
Alwyn
Alwyn
YOU'RE NEVER TOO OLD TO HAVE A HAPPY CHILDHOOD!
Saladin scratchbuild, Matilda scratchbuild, Churchill scratchbuild, Crusader scratchbuild, M10 Achiĺles scratchbuild, Universal Carrier scratchbuild
Saladin scratchbuild, Matilda scratchbuild, Churchill scratchbuild, Crusader scratchbuild, M10 Achiĺles scratchbuild, Universal Carrier scratchbuild
Re: Clark TK24 problems.
Hi guys my transmitter is a JR PCM9X11 the receiver is an Orange R920X v2 on 2.4GHz. It looks like the clark board is not powering the receiver properly. I tried different servos of the same make and model in the board and they do the same thing. They are EMAX ES08MA11.
I have tested them before use on an ESKY EK2-0907 servo adjuster, and a Turnigy servo tester. and all was good before conecting to J2 and J4 on the board. Noiw they over run the stops.
Thank you guys.
Adrian
I have tested them before use on an ESKY EK2-0907 servo adjuster, and a Turnigy servo tester. and all was good before conecting to J2 and J4 on the board. Noiw they over run the stops.
Thank you guys.
Adrian
The South will rise again.
That's South Wales mun Boyo.
.U.K.
That's South Wales mun Boyo.
.U.K.
Re: Clark TK24 problems.
OK I sent the board back to Tankzone for them to look at. I hope its something they can sort out.
Adrian
Adrian
The South will rise again.
That's South Wales mun Boyo.
.U.K.
That's South Wales mun Boyo.
.U.K.
Re: Clark TK24 problems.
They should take care of yougisalook wrote:OK I sent the board back to Tankzone for them to look at. I hope its something they can sort out.
Adrian
Drammen Rock City
