Non-Elevating Tiger Barrel

If you have a tank query and you can't find the answer anywhere else, post here. (TIP - Check for answers in FAQ, use the 'search' facility or even check this board before posting here).
Forum rules
If your question is electronics related please post it in one of the relevant boards here: viewforum.php?f=31
Pebs434
Lance Corporal
Posts: 141
Joined: Mon Jan 04, 2016 4:30 pm

Re: Non-Elevating Tiger Barrel

Post by Pebs434 »

I've opened up the turret as you can see and then wired everything up and there is no noise from the small motor in the curved plastic box thing where the motor and cogs are. It's got to be a dodgy wire connection or the motors shagged I think.
ALPHA
Major-General
Posts: 10960
Joined: Thu Oct 03, 2013 1:06 am

Re: Non-Elevating Tiger Barrel

Post by ALPHA »

Pebs434 wrote:I've opened up the turret as you can see and then wired everything up and there is no noise from the small motor in the curved plastic box thing where the motor and cogs are. It's got to be a dodgy wire connection or the motors shagged I think.
Do you have any kind of spare motor you could plug into the RX...if you do ...just to make sure there is nothing wrong with the RX...plug it in and see if it runs...if it does ...your elevation motor is probably toast ...If you don't have a spare motor laying around....You might be able to plug the smoker into the plug....the motor is about the same size and should activate...don't go too long...just see if it will run ;) If it does...then at least you know the RX is good :thumbup:


ALPHA

PS. Another test to the elevation motor would just pull out the plug and go direct to battery ...first to the contacts on the motor...then to the connector ,,,sometimes the soldered joint comes off on those things ;)
User avatar
43rdRecceReg
Major
Posts: 6295
Joined: Fri Jul 31, 2015 11:38 am
Location: North West Highlands, Scotland

Re: Non-Elevating Tiger Barrel

Post by 43rdRecceReg »

Below: one basic wiring diagram, and one rudimentary DC volt tester (4xAA batteries/ holder/ two probes..all available cheaply from Ebay/ Amazon etc..). There is only one 3-pin connector in the wiring diagram. Disconnect it in at the turret, and put the red probe into
the red connector insert point, and the black into the outside black insertion point (not the middle..that's for airsoft). Movement/ whirring noise means elevate unit is OK...and time to celebrate. If not..you need a new one. It is possible to lose the 'pairing' on your Taigen transmitter, and that might scramble some functions., e.g., everything works but..'rotate' or 'fire'..or well, you get the picture. 'Imex-Erik' explains on Youtube how to rebind your transmitter to the tank...assuming, that is, that you're still using the Taigen stuff:- Note, while 'Imex-Erik" may sound like some sort of Dark Age Viking raider (like 'Sigurd Snake-Eye', and 'Ivar the Boneless'...real raiders), he's actually quite mild and helpful..
Attachments
Simple tester..use on 3 pin connector..
Simple tester..use on 3 pin connector..
Find the three wire connector..
Find the three wire connector..
"Get your facts first, and then you can distort them as much as you please"- Mark Twain.
User avatar
hawkeye3guns
Corporal
Posts: 486
Joined: Wed Dec 09, 2009 12:12 pm
Location: Grantham, Lincs, UK

Re: Non-Elevating Tiger Barrel

Post by hawkeye3guns »

Hi Pebs
Just seen your post. I have 2 or 3 spare elevations motors in my bit box I'll bring them to the meet on Sunday and try and get you going again.
Denzil.
opp's you said get off the road
Pebs434
Lance Corporal
Posts: 141
Joined: Mon Jan 04, 2016 4:30 pm

Re: Non-Elevating Tiger Barrel

Post by Pebs434 »

Thank you Denzil that is very kind of you. Look forward to seeing you there
Pebs434
Lance Corporal
Posts: 141
Joined: Mon Jan 04, 2016 4:30 pm

Re: Non-Elevating Tiger Barrel

Post by Pebs434 »

And thank you too 43rdRecceReg. That is really helpful, I will print it out for future reference and buy one of those testers.
User avatar
43rdRecceReg
Major
Posts: 6295
Joined: Fri Jul 31, 2015 11:38 am
Location: North West Highlands, Scotland

Re: Non-Elevating Tiger Barrel

Post by 43rdRecceReg »

You're very welcome.. :thumbup:
"Get your facts first, and then you can distort them as much as you please"- Mark Twain.
ALPHA
Major-General
Posts: 10960
Joined: Thu Oct 03, 2013 1:06 am

Re: Non-Elevating Tiger Barrel

Post by ALPHA »

hawkeye3guns wrote:Hi Pebs
Just seen your post. I have 2 or 3 spare elevations motors in my bit box I'll bring them to the meet on Sunday and try and get you going again.
Denzil.
:clap: :clap: :clap: Problem sorted ;)


ALPHA
Pebs434
Lance Corporal
Posts: 141
Joined: Mon Jan 04, 2016 4:30 pm

Re: Non-Elevating Tiger Barrel

Post by Pebs434 »

ALPHA
Major-General
Posts: 10960
Joined: Thu Oct 03, 2013 1:06 am

Re: Non-Elevating Tiger Barrel

Post by ALPHA »

Pebs434 wrote:Image
GOOD LUCK PEBS :thumbup:


ALPHA
Post Reply

Return to “General Questions”