Heng Long Pershing Rebuild

ALPHA · Post by **ALPHA** » Thu Sep 11, 2014 5:08 pm

Hey Painless... sorry some family things came up... so won't be till next week that I can get to the Post office

ALPHA

PainlessWolf · Post by **PainlessWolf** » Thu Sep 11, 2014 5:38 pm

Alpha,
No problem, thank you again! ;o) There is plenty of work to do while I wait.
regards,
Painless

ALPHA · Post by **ALPHA** » Thu Sep 11, 2014 7:25 pm

PainlessWolf wrote:Alpha,
No problem, thank you again! ;o) There is plenty of work to do while I wait.
regards,
Painless

Sorry for the delay

ALPHA

PainlessWolf · Post by **PainlessWolf** » Fri Sep 12, 2014 5:30 am

No worries, Alpha ;o) and speaking of some of that work. Nothing in the post today so I took up scribing knife and did one of the least looked forward to bits of detailing that I had in mind. After I removed the sand shields, I sanded the edge of the fenders smooth and using the shields as a template, marked and drilled the bolt holes that removal of those pieces would have left. With a few minutes left over in the evening, I pulled the old HL antenna stub and cut the plastic flat in anticipation of the arrival of Woz's 3D printed tank and radiator caps. Pics:

Jake79 · Post by **Jake79** » Fri Sep 12, 2014 9:16 am

Enjoying following your build,you explain things well, good for us novices to learn a thing or two.

ALPHA · Post by **ALPHA** » Fri Sep 12, 2014 11:43 am

I can tell you love the challenge Painless.... if I were cutting those skirts...the last tool I would grab is a knife

....Dremel or xacto saw

Have to admit...that's some Eye boggling work

....the bolt holes are a nice touch

ALPHA

PainlessWolf · Post by **PainlessWolf** » Fri Sep 12, 2014 3:27 pm

Good Morning, Jake,
Thank you for following along! I learned by watching other guys do the work and show how to make it fun. ;o)
regards,
Painless

PainlessWolf · Post by **PainlessWolf** » Fri Sep 12, 2014 3:34 pm

Alpha,
Thank you for the compliments, my friend. ;o) There were a couple of minutes in the middle of scribing out the last one when I asked myself why I had not fetched the Dremel and put a router bit or blade on it. My fingers were getting pretty sore by that time. It turned out Ok tho'. At least, there was minimal sanding required to clean up the edges plus I now have a workable pair of sand shields for the parts box. The bolt holes were just an afterthought. I'm trying to use my mini Yankee drill more to add easy detailing.
regards,
Painless

ALPHA · Post by **ALPHA** » Sat Sep 13, 2014 3:56 am

PainlessWolf wrote:Alpha,
Thank you for the compliments, my friend. ;o) There were a couple of minutes in the middle of scribing out the last one when I asked myself why I had not fetched the Dremel and put a router bit or blade on it. My fingers were getting pretty sore by that time. It turned out Ok tho'. At least, there was minimal sanding required to clean up the edges plus I now have a workable pair of sand shields for the parts box. The bolt holes were just an afterthought. I'm trying to use my mini Yankee drill more to add easy detailing.
regards,
Painless

The final result is great Painless.... I just couldn't help but thing the first tool I would reach for is my xacto saw

...the last would be the knife....

ALPHA

PainlessWolf · Post by **PainlessWolf** » Sat Sep 13, 2014 7:04 am

Alpha, *grinz* I like my scribing tool set. I used it to get those plastic grills off of Maxine's rear deck and still leave the posts to screw into there. There are plenty of times that I do fire up the Dremel or electric Drill as well. ;o) Nothing Post wise today so I was about to start making the little exterior Fire Extinguisher handle then remembered, "Hey, I think I bought some parts for this tank" Sure enough, that piece and most of the rest of the deck detail that I was about to move from the old tank to the new were on the Tamiya sprues. I contented myself with removing some unneeded HL deck detail and adding the four Mato periscope guards for the front hatches and surrounds by the Blower housing. Plenty of time to have fun this weekend with the rest. Pics: