RC Tank Warfare community hobby forum

Orizzontal left stick work ( cannon up/down)

Vertical left stick up (it work)

Vertical right stick work

Andreabert wrote:Rad
please let me know what i have to do and i will do.
i think i plugged the board correctly follow instuctions...
but enlgish is not my Language.... so.. hard for me to understood all

no problem to use the left stick to drive the tank......the problem is to connect all correctly and have to stick working....

For me it is complicated to give assistence with that radio because I dont owe it, neither one running Open TX. I use another open source software caller erskytx which is about 90% the same.

But I guess first of all you have to go to radio setup and select the mode you want to have, is what our french friend told you.

Then create a new model, and in model setup/mixer select the channel and the stick that controlls that channel. As I said is really easy and fast, once you know how to do it.

Then you need to program the rest of the channels in the switches and potentiometers for the rest of the functions.

If after a while you cannot make it work and you are desperated, you can send it to me so I can make it for you in one day. I am in Austria so shipping is affordable and fast.

Orizzontal right stick NOting work

Andreabert wrote:Here the receiver
I disconnected the red/black to take a pic

That is wrong. Black and wire goes to VCC.all the channels are wrong. You started connecting them in the channel 2.

And the white wire is upside down.

Time to sleep for me.

Rad_Schuhart wrote:

Andreabert wrote:Rad
please let me know what i have to do and i will do.
i think i plugged the board correctly follow instuctions...
but enlgish is not my Language.... so.. hard for me to understood all

no problem to use the left stick to drive the tank......the problem is to connect all correctly and have to stick working....

For me it is complicated to give assistence with that radio because I dont owe it, neither one running Open TX. I use another open source software caller erskytx which is about 90% the same.

But I guess first of all you have to go to radio setup and select the mode you want to have, is what our french friend told you.

Then create a new model, and in model setup/mixer select the channel and the stick that controlls that channel. As I said is really easy and fast, once you know how to do it.

Then you need to program the rest of the channels in the switches and potentiometers for the rest of the functions.

If after a while you cannot make it work and you are desperated, you can send it to me so I can make it for you in one day. I am in Austria so shipping is affordable and fast.

well im using mode 2, the channel order is RTEA

i made a lot of new model.. but every time i got questions i dont know how to reply

have amodel a motor? yes no? wich Chanel..and so on...

Rad_Schuhart wrote:

Andreabert wrote:Here the receiver
I disconnected the red/black to take a pic

That is wrong. Black and wire goes to VCC.all the channels are wrong. You started connecting them in the channel 2.

And the white wire is upside down.

Time to sleep for me.

ohhh shit... im a fucking jerk........
now it work...........shit...
thanks a lot....

I thank the best is to start everything again,and in order an I repeat,take a servo otherwise,you will not get out!!!and tested each output if the Receuver and thus know which stick moves which channel afterwards am I trying to help? Itherwuse ther is Rad's proposition
Good night.i

well guys..
thanks so much

i have your idea when on my forum someone ask me to help him ti identify ww2 weapons (im a collector).. and i usually say...buy the books and read....lol
now im in that situation....

ok now the tank work... basically... turret, cannon and tracks...
i now have to understood how to set up all the other functions..
cannon, mg, etc

what is a servo and why i shoud use it?

for every switch of the radio i should be able to assign a command, right?