RC Tank Warfare community hobby forum

HERMAN BIX wrote: ↑Sat Mar 25, 2023 10:16 pm

mrmetallica wrote: ↑Sat Mar 25, 2023 9:51 pm the little red wire that comes out of the uit near l9 i think is that the wire that connects to the controller wirelessly ? so i can do away with the aerial on the tank ?
sorry but not done this before .

Yes Sir you can do away with the external aerial.
It should be routine enough to get the functions working if you get the plugs changed onto the respective wires for each operation, elevation, rotation and the drive motors, but BB will be the likely sticking point.
Be sure to add a loop wire into the Trigger socket. Just use an old cable, cut it down to an inch long off the plug, bare both wires & join them with solder & heat shrink-done.
That will give you cannon sound .

mrmetallica wrote: ↑Sat Mar 25, 2023 10:36 pm

HERMAN BIX wrote: ↑Sat Mar 25, 2023 10:16 pm

mrmetallica wrote: ↑Sat Mar 25, 2023 9:51 pm the little red wire that comes out of the uit near l9 i think is that the wire that connects to the controller wirelessly ? so i can do away with the aerial on the tank ?
sorry but not done this before .

Yes Sir you can do away with the external aerial.
It should be routine enough to get the functions working if you get the plugs changed onto the respective wires for each operation, elevation, rotation and the drive motors, but BB will be the likely sticking point.
Be sure to add a loop wire into the Trigger socket. Just use an old cable, cut it down to an inch long off the plug, bare both wires & join them with solder & heat shrink-done.
That will give you cannon sound .

thank you for the answer would you have a pic of what you mean about the wire please

mrmetallica wrote: ↑Sat Mar 25, 2023 9:51 pm the little red wire that comes out of the uit near l9 i think is that the wire that connects to the controller wirelessly ? so i can do away with the aerial on the tank ?
sorry but not done this before .

Jofaur86 wrote: ↑Sun Mar 26, 2023 12:19 am I think what Mr. Bix is ​​talking about? concerns the CN 6 socket, where it is necessary to shunt the two pins,( + / - ? ) to have the sound of the gun? but not being sure of me, and advised by him, more courteous, that he answer himself, will avoid possible errors

HERMAN BIX wrote: ↑Sun Mar 26, 2023 3:04 am

Jofaur86 wrote: ↑Sun Mar 26, 2023 12:19 am I think what Mr. Bix is ​​talking about? concerns the CN 6 socket, where it is necessary to shunt the two pins,( + / - ? ) to have the sound of the gun? but not being sure of me, and advised by him, more courteous, that he answer himself, will avoid possible errors

Correct Mr Jofaur, CN6 needs to have a plug with a loop in it. simply a 2-core cable out of the the plug, cut an inch long, bare the ends,join, and solder together.
Voila!!

Jofaur86 wrote: ↑Sun Mar 26, 2023 12:19 am I think what Mr. Bix is ​​talking about? concerns the CN 6 socket, where it is necessary to shunt the two pins,( + / - ? ) to have the sound of the gun? but not being sure of me, and advised by him, more courteous, that he answer himself, will avoid possible errors

mrmetallica wrote: ↑Sun Mar 26, 2023 11:33 am

HERMAN BIX wrote: ↑Sun Mar 26, 2023 3:04 am

Jofaur86 wrote: ↑Sun Mar 26, 2023 12:19 am I think what Mr. Bix is ​​talking about? concerns the CN 6 socket, where it is necessary to shunt the two pins,( + / - ? ) to have the sound of the gun? but not being sure of me, and advised by him, more courteous, that he answer himself, will avoid possible errors

Correct Mr Jofaur, CN6 needs to have a plug with a loop in it. simply a 2-core cable out of the the plug, cut an inch long, bare the ends,join, and solder together.
Voila!!

so basicly short the 2 pins ?

HERMAN BIX wrote: ↑Sun Mar 26, 2023 11:57 am

mrmetallica wrote: ↑Sun Mar 26, 2023 11:33 am

HERMAN BIX wrote: ↑Sun Mar 26, 2023 3:04 am

Correct Mr Jofaur, CN6 needs to have a plug with a loop in it. simply a 2-core cable out of the the plug, cut an inch long, bare the ends,join, and solder together.
Voila!!

so basicly short the 2 pins ?

yip, thats it.