Page 2 of 5

Re: Help Request - Taigen Tiger 1 not binding

Posted: Wed May 26, 2021 9:05 pm
by DaveNorthWales
john1970 wrote:I dont have a V3 controller but can offer an idea. how long does it take for the flashing red light to go out ? if someone else has a V3 controller perhaps they could try the same switch the controller on in binding mode with no tanks switched on and see if the light stops flashing or just continues
Hi John,

About 5 seconds or so. Not very long.

Re: Help Request - Taigen Tiger 1 not binding

Posted: Wed May 26, 2021 9:07 pm
by DaveNorthWales
forgebear wrote:See if this helps.
1. top left chrome switch- push backwards
2. top left right chrome switch - flick forward
3. hold the black button in next to the chrome switch
4 whilst holding this switch, power up your transmitter and then your tank
5. when the red light stops flashing, flick the right chrome switch backwards, flick the left chrome switch forward and the tank should start

if it doesn't flick the left chrome switch back to off, turn your transmitter off. Then turn your transmitter back on and flick the left chrome switch forward again to start
Thanks, Forgebear, I'll try that next time I'm at my brother's, in the next few days. That's where the tank is.

Re: Help Request - Taigen Tiger 1 not binding

Posted: Wed May 26, 2021 9:11 pm
by DaveNorthWales
Jofaur86 wrote::D Hello,

Here is how to proceed, sorry if in French? but google translate is your friend, this is in line with what Forgeaber says, but with the images in addition
https://www.rc-panzershop.fr/ekmps/shop ... /hl2.4.pdf
hi Jofaur86, Thanks for the information, but that's the older controller. The right hand toggle switch on this one is for the smoke unit, there's a new push button for the machine gun.

Re: Help Request - Taigen Tiger 1 not binding

Posted: Wed May 26, 2021 9:11 pm
by DaveNorthWales
Jofaur86 wrote:also on youtube and udeme for all Taigen cars :thumbup:
https://www.youtube.com/watch?v=e-ddQjBcPCY
That's for the older controller too :) .

Re: Help Request - Taigen Tiger 1 not binding

Posted: Wed May 26, 2021 9:16 pm
by DaveNorthWales
This video shows the new controller with the push-button for the machine gun (and then they show the older version too.)

https://www.youtube.com/watch?v=Fd39SnXPGQM

Re: Help Request - Taigen Tiger 1 not binding

Posted: Wed May 26, 2021 11:14 pm
by Jofaur86
okay, but having a machine gun button? for me, should not change the way of "Binder" the transmitter with the receiver? as it was said above? are you sure that the battery is well charged 8O

Re: Help Request - Taigen Tiger 1 not binding

Posted: Thu May 27, 2021 6:02 pm
by Herr Dr. Professor
My experience installing Taigen V3 boards and sound modules and binding Taigen V3 transmitters tells me that Dave is correct: the binding procedure for Taigen V3 is different from the procedure for previous versions. Matthias Lickel, "Licmas" (https://heng-long-panzer.de/de/ or https://heng-long-panzer.de/en/) knows his stuff, and the binding procedure in the first half of the video is correct. I have had good communication from him over the past five or more years.

Dave, did you buy the tank from Lickel?

Re: Help Request - Taigen Tiger 1 not binding

Posted: Thu May 27, 2021 9:32 pm
by DaveNorthWales
Herr Dr. Professor wrote:Dave, did you buy the tank from Lickel?
My brother did, yes.

Matthias is trying to help, but I need to try to at least determine if 1) we're doing it wrong, 2) the controller is at fault, 3) the electronics in the tank are either faulty or wired up wrong.

Re: Help Request - Taigen Tiger 1 not binding

Posted: Thu May 27, 2021 9:35 pm
by DaveNorthWales
Jofaur86 wrote:okay, but having a machine gun button? for me, should not change the way of "Binder" the transmitter with the receiver? as it was said above? are you sure that the battery is well charged 8O
It's the same, but different :)

The right-hand toggle switch used to be the machine gun on/off switch. You had to turn it on and then go through the binding process. Now, you need to hold the push button in to make the machine gun be "on" while you bind. So the machine gun being on is still a requirement to bind, but the physical control has moved to a different switch.

Re: Help Request - Taigen Tiger 1 not binding

Posted: Thu May 27, 2021 10:14 pm
by john1970
silly question on the V3 taigen board you can use a hobby grade transmitter. You havent put the binding plug in it have you?

hobby rc receiver bind plug shouldnt be plugged in

Image