Page 2 of 3
Re: Heng long 2.4ghz 5.3 wiring and Clark tk22
Posted: Thu Jan 31, 2019 10:44 pm
by Jofaur86
Hello,
http://www.clark-model.com/eng/index_e.html
Colonne gauche,voir "!universal Recoil 16011/012/016 "
Re: Heng long 2.4ghz 5.3 wiring and Clark tk22
Posted: Thu Jan 31, 2019 11:05 pm
by c.rainford73
It simply fits in the locations for the two round tips for the airsoft mechanism sit. The rear arm rests on the cam for the stock elevation gearbox and goes up and down or you can adapt for servo elevation too.
Re: Heng long 2.4ghz 5.3 wiring and Clark tk22
Posted: Fri Feb 01, 2019 1:23 am
by AshMann
c.rainford73 wrote:It simply fits in the locations for the two round tips for the airsoft mechanism sit. The rear arm rests on the cam for the stock elevation gearbox and goes up and down or you can adapt for servo elevation too.
Alright, thank you
Re: Heng long 2.4ghz 5.3 wiring and Clark tk22
Posted: Fri Feb 01, 2019 1:30 am
by c.rainford73
Here's a Sherman barrel in action via another builder. I usually thread a small led light through the gun barrel and attach to the appropriate spot on the Clark board.
https://youtu.be/ACznTg5wET4
Sent from my SM-N960U using Tapatalk
Re: Heng long 2.4ghz 5.3 wiring and Clark tk22
Posted: Fri Feb 01, 2019 1:50 am
by AshMann
c.rainford73 wrote:Here's a Sherman barrel in action via another builder. I usually thread a small led light through the gun barrel and attach to the appropriate spot on the Clark board.
https://youtu.be/ACznTg5wET4
Sent from my SM-N960U using Tapatalk
Would the gun need to be modified in order to work with the unit?
Re: Heng long 2.4ghz 5.3 wiring and Clark tk22
Posted: Fri Feb 01, 2019 1:54 am
by c.rainford73
I'm sure everyone has a way to do it, but I usually take a piece of airsoft tube as it's made to fit the barrel nicely and then very carefully fit a proper length of the modified tube into the Clark unit. Make sure the hole in the recoil housing is clear and do not force the tube into the 3D printed part or you can break it. Also remove all burrs and extra plastic flashing so the new recoil moves freely or you can burn out a servo.
Sent from my SM-N960U using Tapatalk
Re: Heng long 2.4ghz 5.3 wiring and Clark tk22
Posted: Sun Feb 03, 2019 5:16 am
by Tinsen
Hi, I'm bought a second hand tank that installed TK22 board.It has 10 A fuse in red wire.It 's necessary to has fuse or not? Thank for all suggestion.
Re: Heng long 2.4ghz 5.3 wiring and Clark tk22
Posted: Mon Feb 04, 2019 10:48 am
by Jofaur86
Hello,
Yes it's better to leave the fuse in case of short circuit installation
Re: Heng long 2.4ghz 5.3 wiring and Clark tk22
Posted: Mon Feb 04, 2019 11:30 am
by Son of a gun-ner
Jofaur86 wrote:Hello,
Yes it's better to leave the fuse in case of short circuit installation
What type of fuse please? I'm guessing not the type that's in a UK 240 volt plug. And there is so many various types of fuses.
Re: Heng long 2.4ghz 5.3 wiring and Clark tk22
Posted: Mon Feb 04, 2019 12:31 pm
by Ludwig von wigbearer
I use 10a car fuse, you can buy pre wired fuse holders and solder in