Page 2 of 3
Re: Henn Tec Idler System
Posted: Thu Sep 17, 2015 5:53 pm
by Guido Henn
Hello Joe,
i am sorry,because i had read this thread to late.
If you need the manual in englisch,please contact me per mail,the i can send a PDF document.
henntec@gmx.de
with regards,Guido
Re: Henn Tec Idler System
Posted: Thu Sep 17, 2015 6:09 pm
by maxmekker
Just installed the HT for my tamiya Leo, Nice system will be buying for my JP/P also, but With my basic School German I was afraid to miss some important info, so pleez consider including in English also in the future
Re: Henn Tec Idler System
Posted: Thu Sep 17, 2015 7:43 pm
by jtracks
Guido Henn wrote:Hello Joe,
i am sorry,because i had read this thread to late.
If you need the manual in englisch,please contact me per mail,the i can send a PDF document.
henntec@gmx.de
with regards,Guido
Thank you Guido, I'll be sure to contact you for the next idler system I install. The system is installed and will work well I'm sure. I like the fact that I can adjust the idler wheels from outside of the tank.
Re: Henn Tec Idler System
Posted: Thu Sep 17, 2015 7:52 pm
by jtracks
Kaiser, thanks very much for the time you took to help me out. Thanks to you, it's up and running, or will be soon. I used a reamer to enlarge the hole due to the fact I didn't have a drill bit large enough. I will also replace the 3mm screws in the 2nd photo with some that are a little shorter. I was able to use an installers drill bit (18 inches long) to drill the 3mm hole from inside of the hull coming from the opposite 12mm hole. Worked out well. Thanks again.
Re: Henn Tec Idler System
Posted: Thu Sep 17, 2015 7:55 pm
by jtracks
Kiaser wrote:Excellent Guido
yes there was a couple of words that sent me never seen them before or could not remember
I noticed that you have two fixing holes on your 2A6 maxmekker
I may consider doing that also.
Re: Henn Tec Idler System
Posted: Thu Sep 17, 2015 9:38 pm
by maxmekker
Re: Henn Tec Idler System
Posted: Thu Sep 17, 2015 9:59 pm
by jtracks
That looks nice and finished, well done.
Re: Henn Tec Idler System
Posted: Fri Sep 18, 2015 6:01 pm
by Max-U52
Guido Henn wrote:Hello Joe,
i am sorry,because i had read this thread to late.
If you need the manual in englisch,please contact me per mail,the i can send a PDF document.
henntec@gmx.de
with regards,Guido
Guido, do you have English instructions for the HL King Tiger? That's the only reason I haven't bought one from you yet, I'm not sure I'll be able to follow the instructions. If you have them in English for the KT please tell me where I can order your idler system for my HL King Tiger.
Re: Henn Tec Idler System
Posted: Fri Sep 18, 2015 7:35 pm
by Guido Henn
Hello,
ETO-Armor in the U.S. sell's all products from me,with manuals in english.
For the HL-KIng-tiger i have no english manual.
Please feel free to contact Robert from ETO,i am sure he can help .
regards,Guido
Re: Henn Tec Idler System
Posted: Fri Sep 18, 2015 8:23 pm
by jtracks
Guido Henn wrote:Hello,
ETO-Armor in the U.S. sell's all products from me,with manuals in english.
For the HL-KIng-tiger i have no english manual.
Please feel free to contact Robert from ETO,i am sure he can help .
regards,Guido
Hello Guido, just so you will know, I purchased my idler from ETO and the instructions are in German.
