A Panzer IV tank made ??of aluminum and is formed with brush

[Edwin]

Hi there,

Today I started with the milling of the first parts of a new Panzer IV tank of aluminum.

k-IMG_3655.JPG (41.5 KiB) Viewed 2371 times

This will now occur the next time.

[MK1 Nut]

Milling your own parts... impressed!

Are you going to be welding the parts together?

Helen x

[Edwin]

hi Mk1,

No, I stick my pans. Since welding is better than when you can.

regards Edwin

[Edwin]

With the first Panzer IV tank, it also goes further.

The parts I have now trimmed, sanded and degreased.

k-IMG_3684.JPG (24.73 KiB) Viewed 2324 times

So I could glue them even today.

k-IMG_3685.JPG (27.13 KiB) Viewed 2324 times

Now they must first remain lying to harden before continuing.

[Edwin]

Because I'm just the same even today I have also glued a second well .....

[Edwin]

This time I have dealt with the aluminum poles that accommodate the chassis mounts.

I had to cut to length every 2 aluminum square rods and Initial milling on one side for the two pans.

k-IMG_3737.JPG (36.42 KiB) Viewed 2250 times

k-IMG_3738.JPG (41.6 KiB) Viewed 2250 times

After I trimmed the edges and removed the bars from the lubricant I could stick to the pans. These are really stable by now.

k-IMG_3739.JPG (39.45 KiB) Viewed 2250 times

[Edwin]

After I wait a little bit longer because of the construction at the Panzer IV until I plastered, I would not know that they go right back broken, today was his turn.

k-IMG_3810.JPG (39.41 KiB) Viewed 2238 times

Then I was able to bend the rear, lower rear panel fits and stick to the pans.

k-IMG_3815.JPG (34.04 KiB) Viewed 2238 times

k-IMG_3816.JPG (34.5 KiB) Viewed 2238 times

So I can no longer handle the tubs and can only go on again tomorrow.

[Edwin]

Today I build the connections of the chain tensioner on the pans.

I will need first two brass pieces that I saw myself with my band saw from a brass rod.

k-IMG_3822.JPG (29.99 KiB) Viewed 2225 times

To each of these two cubes I have to get two saddle for the first release they devour on the outer dimensions

k-IMG_3823.JPG (47.62 KiB) Viewed 2225 times

As a support for the eccentric I turn 4 left 9mm brass tubes and makiere the dice for a central bore.

k-IMG_3825.JPG (29.13 KiB) Viewed 2225 times

There I drill a 9mm hole in the cube which I then separate them with a thin blade in the middle.

k-IMG_3826.JPG (41.88 KiB) Viewed 2225 times

k-IMG_3827.JPG (36.79 KiB) Viewed 2225 times

k-IMG_3828.JPG (39.14 KiB) Viewed 2225 times

Now I have to mill off all the edges to the center.

k-IMG_3830.JPG (34.28 KiB) Viewed 2225 times

So that the chain tensioner is also really stable I solder the pipes and the Bassis hard.

k-IMG_3831.JPG (53.71 KiB) Viewed 2225 times

k-IMG_3832.JPG (68.17 KiB) Viewed 2225 times

After pickling, grinding and I can now stick the first couple of brackets with a tub. Through the brackets plus I put a straight rod 5mm to both align exactly on the sink.

k-IMG_3833.JPG (30.33 KiB) Viewed 2225 times

Tomorrow I can then glue the brackets on the second well.

[Edwin]

In small pieces I continue.

The rear end I can always stick, piece by piece, slowly but it grows.

k-IMG_3838.JPG (31.78 KiB) Viewed 2208 times

For this, the second well has also received the supports for the chain tensioner.

k-IMG_3839.JPG (39.14 KiB) Viewed 2208 times

[lliw180]

looking good mate