clark board airsoft problem

lister fiend · Post by **lister fiend** » Sat May 04, 2013 3:29 pm

hi all.
i have 2 tk20's which won't fire bb's.
i got a remote & hbu to program it, but to no avail

apart from this they work & sound good.
any thoughts anyone?
thanks in advance
lister

MichaelC · Post by **MichaelC** » Sat May 04, 2013 3:43 pm

lister, is it accepting the programming in Airsoft mode and it still doesn't fire, or you can't get it to program at all ?

lister fiend · Post by **lister fiend** » Sat May 04, 2013 4:22 pm

I'm pretty sure I've programmed it
Correctly ( 2 flashes )
But I'm obviously doing something wrong

It's probably obvious & I just can't see it for
Looking.
Any thoughts?

MichaelC · Post by **MichaelC** » Sat May 04, 2013 4:28 pm

You did the re-wiring, right ? It wasn't clear on the website but I seem to recall that mine didn't work either until I did the re-wiring of splitting out the elevation motor with the airsoft motor.

lister fiend · Post by **lister fiend** » Sat May 04, 2013 4:35 pm

Great, thanks Michael

No I haven't, looks like I better crack out
The soldering iron out!
The weather's finally turned here,
So want to get out there

I'll let you know if it works
Cheers
Lister

lister fiend · Post by **lister fiend** » Sat May 04, 2013 5:11 pm

ah crapola

my tiger is a bit different to the one on the website
& i can't quite get my head around it

so if i've got this right, i need to put an extra wire from the elavation wire on the safty switch,
& put it where?
oh dear i just can't see it

MichaelC · Post by **MichaelC** » Sat May 04, 2013 5:55 pm

I have done this 3 times now and I am still confused about it but if you just look at the two colour coded before and after on the 8 pin connectors on the wiring, what you are trying to do is instead of taking the power from the elevation motor (PIN 4 from the left or the Yellow port on the diagram) to the saftey switch and then onto the Airsoft unit, you are now taking the constant power from the MG/Light etc which is PIN 6 from the left or the Green port on the diagram. That way you will have independent control of the elevation and power to the Airsoft.

So if you can isolate the power feed to the safty switch, either from the elevation motor or the PIN 4 from the 8 pin board, just move that wire to goto PIN 6 on the board instead.

lister fiend · Post by **lister fiend** » Tue May 07, 2013 9:50 pm

hi michael,
i'm still having issues here.
i rewired it but when i fire the gun it just keeps going

i then tried bypassing it all and just wiring the elavation & airsoft straight in & repeat of the above

any sugestions welcomed!
cheers
lister

MichaelC · Post by **MichaelC** » Tue May 07, 2013 11:26 pm

Hey lister, so before the re-wiring the BB was not functioning at all, and after the wiring as describe on the website it is firing all the time (i.e. won't stop firing) ? You did the programming already to Airsoft BB on the clark I think. (Power on the remote, and then flash twice). Hmmmm..... usually when I have a non-stop firing it is because the power going into it is flipped, but you check the wiring already. I have to open up mine to have a look-see now.

lister fiend · Post by **lister fiend** » Wed May 08, 2013 12:44 am

thanks,
when you say flipped, do you mean, i might have the wires round the wrong way?

RC Tank Warfare community hobby forum

clark board airsoft problem

clark board airsoft problem

Re: clark board airsoft problem

Re: clark board airsoft problem

Re: clark board airsoft problem

Re: clark board airsoft problem

Re: clark board airsoft problem

Re: clark board airsoft problem

Re: clark board airsoft problem

Re: clark board airsoft problem

Re: clark board airsoft problem