Conqueror!
-
- Warrant Officer 2nd Class
- Posts: 1343
- Joined: Tue Dec 17, 2019 12:27 am
Re: Conqueror!
I’m not printing the conquer yet but I am doing the commet, and my dad is doing a secret project I’m not supposed to know about both are being resin and look to be turning out well
It’s your tank it’s what you make it
-
- Warrant Officer 2nd Class
- Posts: 1343
- Joined: Tue Dec 17, 2019 12:27 am
Re: Conqueror!
Although along with the hellcat chafee Churchill easy 8 the conquer is on the list, its looking good on the fillament printers
It’s your tank it’s what you make it
Re: Conqueror!
Hello,
here the comparison with Centurion, FV4005 and at least a Churchill Mk.VII
here the comparison with Centurion, FV4005 and at least a Churchill Mk.VII
-
- Warrant Officer 2nd Class
- Posts: 1343
- Joined: Tue Dec 17, 2019 12:27 am
Re: Conqueror!
I have reservations about those printed tracks. How do they hold out on different surfaces.
It’s your tank it’s what you make it
Re: Conqueror!
The tracks printed of PETG are just as strong as the Tamiya tracks.Exhibitedbrute wrote: ↑Sun Apr 14, 2024 8:18 pm I have reservations about those printed tracks. How do they hold out on different surfaces.
I was also skeptical at first, but I did a strength and tensile test and attached 10 kg.
That was no problem at all.
You have to pay attention to the alignment when printing because of the "fiber flow" and choose a slightly higher temperature.
- tankme
- Warrant Officer 1st Class
- Posts: 2022
- Joined: Tue Oct 31, 2017 3:51 pm
- Location: Elgin, TX
- Contact:
Re: Conqueror!
Good thing about 3D printed tracks...if they fail, you can always print more and can try them in a different material. My Tortoise tracks were just printed in Sunlu ABS like resin so I'll see how strong those are.
Derek
Too many project builds to list...
Too many project builds to list...
-
- Warrant Officer 2nd Class
- Posts: 1343
- Joined: Tue Dec 17, 2019 12:27 am
Re: Conqueror!
Let me know about those resin track because I plan printing the commet ones in anycubic abs like resin and I would assume that the Matilda my dads printing for my birthday that I’m not supposed to know about will have them aswell
It’s your tank it’s what you make it
- tankme
- Warrant Officer 1st Class
- Posts: 2022
- Joined: Tue Oct 31, 2017 3:51 pm
- Location: Elgin, TX
- Contact:
Re: Conqueror!
The Sunlu ABS Like isn't as non-brittle as I'd like. I does flex some before breaking, but small ridges tend to be brittle. I've got both Tortoise tracks printed and pinned so it's just a matter of finishing the suspension on that thing before I can do some testing on it. For future tracks, I may mix some Siraya Tenacious into the ABS like. I think I printed my Comet tracks in PETG as it was pre-resin printer. They were a royal PITA to clean up the supports. I'm still very new to resin printing so I've been experimenting with different things.
Derek
Too many project builds to list...
Too many project builds to list...
Re: Conqueror!
Hello,
a little step forward...
I soldered the cargo together with silver solder:
Assembled and painted:
a little step forward...
I soldered the cargo together with silver solder:
Assembled and painted:
Re: Conqueror!
Nice! I think I'll be doing mine in resin, as I have neither the skills nor the patience to solder something that intricate