Lads, have an old taigen Tiger 1 that has been retrofitted with the newer V3 set.
Everything works bar the elevation & recoil. Its like the unit in the turret has no power to it.
There is an on/off switch in the loaders hatch that i have tried in both positions, not sure what it does or why its there, but still nothing.
I have had the recoil/elevation unit out and all the wiring appears intact.
This tank HAS worked properly since the V3 was installed but been shelved for 3 odd years pending its owner to rekindle the tank-romance.
Battery fully charged
Switches in right place
I swapped out another motherboard that was new
still not working.
Could be the odd on/off switch is kaput but I cant check it.
any ideas folks ?
TAIGEN V3 TIGER RECOIL PROBLEM
Forum rules
If your question is electronics related please post it in one of the relevant boards here: viewforum.php?f=31
If your question is electronics related please post it in one of the relevant boards here: viewforum.php?f=31
-
HERMAN BIX
- Major-General
- Posts: 11380
- Joined: Sun Jan 12, 2014 12:15 am
- Location: Gold Coast,Australia
TAIGEN V3 TIGER RECOIL PROBLEM
HL JAGDPANTHER,HL TIGER 1,HL PzIII MUNITIONSCHLEPPER, HL KT OCTOPUS,HL PANTHER ZU-FUSS,HL STuG III,HL T34/85 BEDSPRING,
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
Re: TAIGEN V3 TIGER RECOIL PROBLEM
Had the same problem Herman, think the boards failed on this circuit. It usually a common positive a switched negative
Sent from my SM-S901B using Tapatalk
Sent from my SM-S901B using Tapatalk
-
Kaczor
- Warrant Officer 1st Class
- Posts: 2243
- Joined: Fri May 18, 2018 9:58 am
- Location: Ciechanow, Poland
- Contact:
Re: TAIGEN V3 TIGER RECOIL PROBLEM
Do you have this type of elevation and recoil unit?
- Attachments
-
- recoil.png (55 KiB) Viewed 1414 times
-
HERMAN BIX
- Major-General
- Posts: 11380
- Joined: Sun Jan 12, 2014 12:15 am
- Location: Gold Coast,Australia
Re: TAIGEN V3 TIGER RECOIL PROBLEM
Yes Sir it is
HL JAGDPANTHER,HL TIGER 1,HL PzIII MUNITIONSCHLEPPER, HL KT OCTOPUS,HL PANTHER ZU-FUSS,HL STuG III,HL T34/85 BEDSPRING,
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
-
HERMAN BIX
- Major-General
- Posts: 11380
- Joined: Sun Jan 12, 2014 12:15 am
- Location: Gold Coast,Australia
Re: TAIGEN V3 TIGER RECOIL PROBLEM
I did wonder but swapped to another motherboard wioth no change.
Perhaps the actual unit itself is the problem, but Im not convinced that tiny on/off switch is also not at fault.
HL JAGDPANTHER,HL TIGER 1,HL PzIII MUNITIONSCHLEPPER, HL KT OCTOPUS,HL PANTHER ZU-FUSS,HL STuG III,HL T34/85 BEDSPRING,
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
-
Son of a gun-ner
- Lieutenant-Colonel
- Posts: 7533
- Joined: Sun May 07, 2017 8:49 pm
- Location: Lancashire UK
Re: TAIGEN V3 TIGER RECOIL PROBLEM
The on off switch under the turret hatch is for safety, it's for switching the BB unit on and off, to stop accidental pellet firing with the transmitter.
I've no idea why it would be needed with a non BB mechanism.
I've no idea why it would be needed with a non BB mechanism.
Mick - The grit in the underpants of life!
Always happy to spare the bytes
Apparently my mind works in mysterious ways
TOTM needs YOU
support YOUR TOTM competition, I'm doing my part, are YOU?
Always happy to spare the bytes
Apparently my mind works in mysterious ways
TOTM needs YOU
support YOUR TOTM competition, I'm doing my part, are YOU? -
Kaczor
- Warrant Officer 1st Class
- Posts: 2243
- Joined: Fri May 18, 2018 9:58 am
- Location: Ciechanow, Poland
- Contact:
Re: TAIGEN V3 TIGER RECOIL PROBLEM
In my case recoil motor burned. I swapped it with another one from my stash.
-
Jofaur86
- Warrant Officer 1st Class
- Posts: 2172
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: TAIGEN V3 TIGER RECOIL PROBLEM
Good morning,
Herman this small switch, was used on the Tir BB system to cut it, in the case of the Asiatam mechanism? it is advisable to delete it. Moreover, if you put this old Tiger I aside for a few years? and what was working? look if not blocked, the fat drying, sometimes blocks the mechanism.
Herman this small switch, was used on the Tir BB system to cut it, in the case of the Asiatam mechanism? it is advisable to delete it. Moreover, if you put this old Tiger I aside for a few years? and what was working? look if not blocked, the fat drying, sometimes blocks the mechanism.
-
Jofaur86
- Warrant Officer 1st Class
- Posts: 2172
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: TAIGEN V3 TIGER RECOIL PROBLEM
forgot to attach, old HL system diagram for BB shooting
- 34B05829-9E1B-4323-8B2F-BDA69421CB57.jpeg (81.32 KiB) Viewed 1397 times
