I'd like to start a Clark board info page.

Discussion for Clark electronics.
Post Reply
Biasphere1
Lance Corporal
Posts: 137
Joined: Sat Oct 03, 2020 4:34 am

I'd like to start a Clark board info page.

Post by Biasphere1 »

OK so the holy grail pages http://www.clark-model.com/eng/index_e.html
Some TK40 info https://www.youtube.com/watch?app=desktop&v=K5bJ4hcaEJI
Feel free to add what you know as well.
If a moderator could put the pictures to the relevant wording that would be grouse .
Attachments
FS-i6s_10-300x158.jpg
FS-i6s_10-300x158.jpg (15.14 KiB) Viewed 2162 times
KX9nLUi.jpg
KX9nLUi.jpg (44.67 KiB) Viewed 2165 times
Last edited by Biasphere1 on Sun Aug 07, 2022 6:53 am, edited 3 times in total.
Biasphere1
Lance Corporal
Posts: 137
Joined: Sat Oct 03, 2020 4:34 am

Re: I'd like to start a Clark board info page.

Post by Biasphere1 »

How to Setup FlySky i6s Radio with a Clark SBUS TK Board
Plug the FlySky FS-iA10B or FS-iA6B receiver wire from the TK board into the receivers port labeled as SERVO.
NOTE – This will apply only to CH1 of the TK40/TK50 series board if there are multiple receiver leads. Other receiver leads will not be connected in this scenario.
NOTE – There will be only only receiver lead from the TK board for TK60/TK80 series boards.
Make sure the receiver wire is plugged in correctly.
NOTE – The metal contacts will face outwards and the wires will generally be colored from left to right – black, red, white.

On the FlySky i6s radio, tap on the Settings icon.

Tap on the System menu tab

Tap on the Output Mode menu tab, then tap on both PWM and S.BUS.
PIcture at foot of page .

Tap on the Function menu tab, then tap on the Aux. channels option.

Tap on channels 5-10 and assign as follows:






NOTE: Channel 9 is your main cannon and MG1. Swap the channel mapping, with CH9 to VrA and CH10 to VrB to map main canon to VrA.
To set your drive stick as the RIGHT stick – under the System menu, go to Sticks mode, and set as M2
To set your drive stick as the LEFT stick – under the System menu, go to Sticks mode, and set as M3Tap on the Function menu tab, then tap on the Aux. channels option.

Tap on channels 5-10 and assign as follows:






NOTE: Channel 9 is your main cannon and MG1. Swap the channel mapping, with CH9 to VrA and CH10 to VrB to map main canon to VrA.
To set your drive stick as the RIGHT stick – under the System menu, go to Sticks mode, and set as M2
To set your drive stick as the LEFT stick – under the System menu, go to Sticks mode, and set as M3
Attachments
FS-i6s_9.jpg
FS-i6s_8.jpg
FS-i6s_7.jpg
FS-i6s_6.jpg
FS-i6s_5.jpg
sbus menu.jpg
sbus menu.jpg (48.89 KiB) Viewed 2163 times
Biasphere1
Lance Corporal
Posts: 137
Joined: Sat Oct 03, 2020 4:34 am

Re: I'd like to start a Clark board info page.

Post by Biasphere1 »

TK24S dedicated page .
S.BUS setup ( FlySky i6S )

Transmitter:

1.Turn on Transmitter i6s and enter setting function, go to system->output mode, than set Serial to S.BUS



2. Enter aux channel setup, set channel 5 to SwA, channel 6 to SwD, channel 7 to SwB, channel 8 to SwC, channel 9 to VrA and channel 10 to VrB,

3. Go to system->stick mode, then set to M1 mode,

4. Go to end points page, set end point to 100% for every channel.



Receiver and control board:

1. Plug connector with S.BUS label on it into S.BUS port on receiver.
Attachments
sbus menu.jpg
sbus menu.jpg (48.89 KiB) Viewed 2161 times
User avatar
maxmekker
Warrant Officer 1st Class
Posts: 1696
Joined: Tue Apr 27, 2010 8:47 am
Location: Norway

Re: I'd like to start a Clark board info page.

Post by maxmekker »

:thumbup:
Drammen Rock City
User avatar
c.rainford73
Major
Posts: 6104
Joined: Thu Aug 25, 2016 7:34 pm
Location: Connecticut USA

Re: I'd like to start a Clark board info page.

Post by c.rainford73 »

Nice job clear and simple :thumbup:
Tanks alot.... :wave:
Biasphere1
Lance Corporal
Posts: 137
Joined: Sat Oct 03, 2020 4:34 am

Re: I'd like to start a Clark board info page.

Post by Biasphere1 »

If any of you fine people have Clark board ,know a youtube instructional video or have Sony programmer instruction PDF's feel free to post up here please .
My Sony remote and configuration kit from Kenny at DAKRCTANK is on it's way , so I might be able to post up if it comes with instructions. I sorta hope it does .lol
Cheers .
User avatar
Markocaster
Staff Sergeant
Posts: 991
Joined: Mon Mar 31, 2014 11:16 pm
Location: Bay Area , California

Re: I'd like to start a Clark board info page.

Post by Markocaster »

Super helpful post. Cheers


Sent from my iPhone using Tapatalk
HL /Mato tiger 1 early, Tamiya Tiger 1 early, Taigen tiger 1 mid
Taigen T34/85, HL SU-100
Jagdpanzer Lang
Taiga Jagdpanther
Heng Long Sherman DGS Firefly kit
Tamiya King Tiger (unbuilt)
Mato all metal Panzer III
1/10 Jagdpanther
Biasphere1
Lance Corporal
Posts: 137
Joined: Sat Oct 03, 2020 4:34 am

Re: I'd like to start a Clark board info page.

Post by Biasphere1 »

Biasphere1
Lance Corporal
Posts: 137
Joined: Sat Oct 03, 2020 4:34 am

Re: I'd like to start a Clark board info page.

Post by Biasphere1 »

TBA problems lol.
Post Reply

Return to “Clark”