DUKW Scratch Builds 1/16 & 1/9.25
- Ecam
- Warrant Officer 1st Class
- Posts: 1589
- Joined: Sun Jul 13, 2014 6:30 pm
- Location: Lake of the Ozarks, USA
DUKW Scratch Builds 1/16 & 1/9.25
It's going to be a little while until I get these started (M7 has to clear the bench first. Pictured are the 1/35 reference model, the roughly 1/16 (based on two of the HL trucks when they first came out). And the huge frame, axle and propeller kit that was offered by my brother. This may also be some of the first published pictures of Mike's work.
In this picture the Priest is in showing the scale.
In this picture the Priest is in showing the scale.
Last edited by Ecam on Sat May 25, 2024 1:32 am, edited 1 time in total.
"Don't believe everything you see on the internet" - George S. Patton
Eric
Eric
- Model Builder 4
- 2nd Lieutenant
- Posts: 2380
- Joined: Sun Jul 26, 2015 3:46 pm
- Location: South Wales valleys
- Contact:
Re: DUKW Scratch Builds
Following along with these builds Eric, this surely is an ambitious project especially the larger of the three, that one is going to be hugh as you say have you calculated the length of that one yet The 1/16 version should be approximately 21½ inches long give or take, are you planning on making them sea worthy ( or pond worthy ) now that would be a sight to behold
Cheers,Lee.
Cheers,Lee.
Me ? Addicted ? Never !!
- Ecam
- Warrant Officer 1st Class
- Posts: 1589
- Joined: Sun Jul 13, 2014 6:30 pm
- Location: Lake of the Ozarks, USA
Re: DUKW Scratch Builds
Big one (monster) should be about 40 inches. What is a duck that can't swim? Mike did a bunch of calculating and measuring 5 years ago when he started this project. I spent the first part of the morning calculating and intend only to add 3/8" to the wheel base. The width is set by the axles, tires are what they are so the wheelbase is about all I can change to get things as close as I can. I calculated scales of tires, track and WB and came up with an average scale of 1/9.25.
Couldn't resist starting a little. I intend on doing the two simultaneously, but the experiment to build the hull will fall to the 1/16th before the big one.
(12/21/22)
Edit to question above:
Full size the DUKW measured 372" (31 feet) scaled to 1/16th that ends up 23.25 inches. That is how my plans enlarged (218%). That is also how my kit came out including the forward winch hawse.
Couldn't resist starting a little. I intend on doing the two simultaneously, but the experiment to build the hull will fall to the 1/16th before the big one.
(12/21/22)
Edit to question above:
Full size the DUKW measured 372" (31 feet) scaled to 1/16th that ends up 23.25 inches. That is how my plans enlarged (218%). That is also how my kit came out including the forward winch hawse.
Last edited by Ecam on Thu Dec 22, 2022 1:43 am, edited 2 times in total.
"Don't believe everything you see on the internet" - George S. Patton
Eric
Eric
- Ecam
- Warrant Officer 1st Class
- Posts: 1589
- Joined: Sun Jul 13, 2014 6:30 pm
- Location: Lake of the Ozarks, USA
Re: DUKW Scratch Builds
A little of last night's work.
Eventually the hull top will be secured to the lower. So for access to the innards, the cargo deck, crew compartment and possibly the engine cover will be removable. This is all .060/1.5mm sheet, the ribbing underneath is simply for strength since most of the middle will be removeable. Some will need trimming as the lower and innards come together.
By the way, my 0.060 sheets (6x24") were remnants from a sign/graphics shop a friend gave to me. He said they usually end up in the trash can, so he saved me a couple weeks worth (around 50 of them). I have bought full sheets of styrene 4x8 feet at a plastic company/dist. in Denver. .080 was about $44 per sheet. So if you don't have a plastics distributor near you check with your local sign/graphics shop. FAR cheaper than the paper sized stuff available at the hobby shop.
I have used these styrene sheets for about seven years. It works with model, epoxy and super glues. I built a dash pod for a famous Honda S2000 here in the states known as the Big Bad Wolf. And a custom gauge pod for a custom truck (and to hide a hole in the top of the dash where the speaker used to be). Both have seen heat and the race car a bunch of abuse are are none the worse for wear.
The triangles and double wall around the cab are filled with epoxy. Probably over kill, but one of the weaker parts of the hull when cab and cargo deck are out.
Eventually the hull top will be secured to the lower. So for access to the innards, the cargo deck, crew compartment and possibly the engine cover will be removable. This is all .060/1.5mm sheet, the ribbing underneath is simply for strength since most of the middle will be removeable. Some will need trimming as the lower and innards come together.
By the way, my 0.060 sheets (6x24") were remnants from a sign/graphics shop a friend gave to me. He said they usually end up in the trash can, so he saved me a couple weeks worth (around 50 of them). I have bought full sheets of styrene 4x8 feet at a plastic company/dist. in Denver. .080 was about $44 per sheet. So if you don't have a plastics distributor near you check with your local sign/graphics shop. FAR cheaper than the paper sized stuff available at the hobby shop.
I have used these styrene sheets for about seven years. It works with model, epoxy and super glues. I built a dash pod for a famous Honda S2000 here in the states known as the Big Bad Wolf. And a custom gauge pod for a custom truck (and to hide a hole in the top of the dash where the speaker used to be). Both have seen heat and the race car a bunch of abuse are are none the worse for wear.
The triangles and double wall around the cab are filled with epoxy. Probably over kill, but one of the weaker parts of the hull when cab and cargo deck are out.
"Don't believe everything you see on the internet" - George S. Patton
Eric
Eric
- Ecam
- Warrant Officer 1st Class
- Posts: 1589
- Joined: Sun Jul 13, 2014 6:30 pm
- Location: Lake of the Ozarks, USA
Re: DUKW Scratch Builds
Finished what I needed on the top hull. Did not intend to complete the cab as much as I did. As it worked out the cargo bed is held in place with the cab and it by the nose. Therefore needed to get most of it finished.
And then the complex lower hull begins.
And then the complex lower hull begins.
Last edited by Ecam on Thu Dec 22, 2022 1:09 am, edited 1 time in total.
"Don't believe everything you see on the internet" - George S. Patton
Eric
Eric
- Herr Dr. Professor
- Lieutenant
- Posts: 3896
- Joined: Mon Apr 22, 2019 10:48 pm
- Location: Southern Wisconsin USA
Re: DUKW Scratch Builds
I applaud the pedals, levers, and steering wheel, too! Though small, those add so much, even if they aren't such a challenge to you. Then, too, I would bet the tour promoters at Wisconsin Dells would highly approve of your DUKW.
Last edited by Herr Dr. Professor on Wed May 25, 2022 2:54 am, edited 1 time in total.
- Ecam
- Warrant Officer 1st Class
- Posts: 1589
- Joined: Sun Jul 13, 2014 6:30 pm
- Location: Lake of the Ozarks, USA
Re: DUKW Scratch Builds
The levers were really an experiment to see if I could make knobs. The black ones are melted sprue, the white is CA glue with a water spray mist to solidify and the clear ones are two part epoxy. The rods are from TIG welding wire that I have a bunch of. The levers shown are about a third (best) of the ones I made. Steering wheel is from a HL truck cab that donated the axles for this project.
"Don't believe everything you see on the internet" - George S. Patton
Eric
Eric
- Ecam
- Warrant Officer 1st Class
- Posts: 1589
- Joined: Sun Jul 13, 2014 6:30 pm
- Location: Lake of the Ozarks, USA
Re: DUKW Scratch Builds
This was more complicated than I thought.
These are my exhaust pipe molds for the fender contours and propeller well.
The brace between rear fenders is temporary.
I'm not pleased with the nose yet. Working with 2D plans to make a 3D model when there are curves and angles is proving tricky.
These are my exhaust pipe molds for the fender contours and propeller well.
The brace between rear fenders is temporary.
I'm not pleased with the nose yet. Working with 2D plans to make a 3D model when there are curves and angles is proving tricky.
"Don't believe everything you see on the internet" - George S. Patton
Eric
Eric
- Ecam
- Warrant Officer 1st Class
- Posts: 1589
- Joined: Sun Jul 13, 2014 6:30 pm
- Location: Lake of the Ozarks, USA
Re: DUKW Scratch Builds
Got the rear suspension located and started on propeller well.
"Don't believe everything you see on the internet" - George S. Patton
Eric
Eric