closer look of the GB platform fasterners flushed to the hull panel
both tracks installed!
Heng Long tanks:
KV-1E
KV-2 MT-1&2
M41
King tiger
Jagdpanther
IJA Type 5 heavy 160ton (to be 3d printed)
FCM F1 (awaiting electronics)
Jagdpanzer E-100 (3D printing in progress)
installed the roof bits
W H E E L E S
Now strike a pose with them turrets~!
improved structural hull framing to increase hull rigidity
Heng Long tanks:
KV-1E
KV-2 MT-1&2
M41
King tiger
Jagdpanther
IJA Type 5 heavy 160ton (to be 3d printed)
FCM F1 (awaiting electronics)
Jagdpanzer E-100 (3D printing in progress)
i feel satisfied with my current progression of the tank and i cant wait to get it up and running!
also size comparison next to a 10ML Tamiya paint bottle
Heng Long tanks:
KV-1E
KV-2 MT-1&2
M41
King tiger
Jagdpanther
IJA Type 5 heavy 160ton (to be 3d printed)
FCM F1 (awaiting electronics)
Jagdpanzer E-100 (3D printing in progress)
now for a better size comparison i placed it next to a Heng Long Jagdpanther of the same scale 1:16. yes i made this beastly french baguette barge 1:16 scale hahahahahahah
hoo boy... im gonna have a total fun time trying to steer this beast
Heng Long tanks:
KV-1E
KV-2 MT-1&2
M41
King tiger
Jagdpanther
IJA Type 5 heavy 160ton (to be 3d printed)
FCM F1 (awaiting electronics)
Jagdpanzer E-100 (3D printing in progress)
HERMAN BIX wrote:sOOOOOO good to see you back mate thought you might have given up.
Hell of a project you have there.
I dont care if it takes 5 years, as long as you finish it and post it here Im a happy camper
i never given up cause it'll be a costly waste if i stop to where it was. PLUS i have the track models and such. track tension is done so now that is left is to do the turret internals and bring this beast to life.
any suggestions for recommended servo sizes and its mounting layouts? cause right now the main turret and secondary turrets are very much empty
Heng Long tanks:
KV-1E
KV-2 MT-1&2
M41
King tiger
Jagdpanther
IJA Type 5 heavy 160ton (to be 3d printed)
FCM F1 (awaiting electronics)
Jagdpanzer E-100 (3D printing in progress)
FredtheFrench wrote:Just one word in my head: HUGE!!!!!
you wouldnt believe the size of the IJA Type 5 heavy compared to this big boy
Heng Long tanks:
KV-1E
KV-2 MT-1&2
M41
King tiger
Jagdpanther
IJA Type 5 heavy 160ton (to be 3d printed)
FCM F1 (awaiting electronics)
Jagdpanzer E-100 (3D printing in progress)
remade the gun barrel with a better version with the cradle modeled in the dummy recoil cylinder. servo mountings will be added later.
Heng Long tanks:
KV-1E
KV-2 MT-1&2
M41
King tiger
Jagdpanther
IJA Type 5 heavy 160ton (to be 3d printed)
FCM F1 (awaiting electronics)
Jagdpanzer E-100 (3D printing in progress)
gun installed into the FCM's main turret for dry fitting, and added a dummy crewman for a size comparison of it for proportions. added turret roof framing so the turret roof doesnt slide off and fall inside.
Heng Long tanks:
KV-1E
KV-2 MT-1&2
M41
King tiger
Jagdpanther
IJA Type 5 heavy 160ton (to be 3d printed)
FCM F1 (awaiting electronics)
Jagdpanzer E-100 (3D printing in progress)
Hello everybody, as of this current point of the FCM F1.
the things i need to iron out and bug squash on the model for 3d printing to become a full production model as follows:
Hull:
[X] rear part of the tank is not following the schematics due to earlier oversight and lack of information on the hull details
-going to make the hull in 2 halves is possible to fit in with the printer Creality CR-10S S4 400x400x400 size printer and the CR-10 MAX 450x450x500 size printer
-reworking the hull roof to incorporate the catwalks with the hull roof panels in 2 parts.
-hull roof remain as a 3 piece unit
-allocate wiring holes for lighting features
-allocate servo mounting for turrets
[X] hull side panel redone with better build quality
Suspension
-increase structural rigidity, battery housing found to be bowing upwards where the suspension bogie is attached.
-reprint all the tank road wheels with smaller diameter and rim to remain the same size to accommodate wheel rim to touch track panel, further decreasing track throws.
[X] track possible reprint of a better variant
Turret
-servo placement on forward turret needs to be designed
internals
-get them.
Last edited by Giganaut on Tue Nov 26, 2019 11:20 am, edited 2 times in total.
Heng Long tanks:
KV-1E
KV-2 MT-1&2
M41
King tiger
Jagdpanther
IJA Type 5 heavy 160ton (to be 3d printed)
FCM F1 (awaiting electronics)
Jagdpanzer E-100 (3D printing in progress)