Mother board for tigar that’s Lopo safe??

Tomcoles · Post by **Tomcoles** » Sat Mar 10, 2018 4:38 pm

Does anyone know of a mother board that can handle a lipo battery being connected to it? And if so what voltage battery pack is suitable.

midlife306 · Post by **midlife306** » Sat Mar 10, 2018 4:41 pm

The documentation on my IBU2U says it will take up to 3S Lipo, but I run mine on 2S.
Cheers
Wayne

Sent from my iPhone using Tapatalk

rochesb · Post by **rochesb** » Sat Mar 10, 2018 4:56 pm

Open Panzer board will take 2S or 3S batteries, it is good for 7-15V

Max-U52 · Post by **Max-U52** » Sat Mar 10, 2018 5:05 pm

The stock V2 MFU from Taigen is also set up to handle 2S lipo. As far as I know, the Clark series and the Tamiya electronics are set for 7.2 nicads or nimhs or 7.4 lipo or li-ion and won't handle 12 volts (11.1 3S). I believe elmod will handle 3S but I'm not positive about that. I'm sure someone here will know.

Tomcoles · Post by **Tomcoles** » Sat Mar 10, 2018 5:13 pm

It’s the v2 I am most interested in I think

Max-U52 · Post by **Max-U52** » Sat Mar 10, 2018 5:41 pm

Here's the V2 in my Panzer III, running on a Nanotec 2200 Mah lipo battery

phpBB [video]

This tank is still for sale, BTW.

It drives just great, even though that's not shown in the video.

Post by **maxmekker** » Sat Mar 10, 2018 6:19 pm

Clark tk24 2s lipo
Clark tk60 3s lipo

Tomcoles · Post by **Tomcoles** » Sat Mar 10, 2018 6:28 pm

Great thankyou

jarndice · Post by **jarndice** » Sat Mar 10, 2018 6:40 pm

Some years ago one of us reported a burned out new CLARK board while using a LI-PO,
The accepted advise was with a new CLARK board use a NI-MH or a NI-CAD for the boards first use and then use a LI-PO,
It appears by doing it that way it "Hardens" the new board,
I don't know if it is true but every new board that I use always gets hooked upto a NI-MH for its first use and then I go to a LI-PO and I have never had a burned out board.
Shaun.

Post by **maxmekker** » Sat Mar 10, 2018 9:03 pm

jarndice wrote:Some years ago one of us reported a burned out new CLARK board while using a LI-PO,
The accepted advise was with a new CLARK board use a NI-MH or a NI-CAD for the boards first use and then use a LI-PO,
It appears by doing it that way it "Hardens" the new board,
I don't know if it is true but every new board that I use always gets hooked upto a NI-MH for its first use and then I go to a LI-PO and I have never had a burned out board.
Shaun.

I'll check that out . Might be the tk22 'way' of doing it .

RC Tank Warfare community hobby forum

Mother board for tigar that’s Lopo safe??

Mother board for tigar that’s Lopo safe??

Re: Mother board for tigar that’s Lopo safe??

Re: Mother board for tigar that’s Lopo safe??

Re: Mother board for tigar that’s Lopo safe??

Re: Mother board for tigar that’s Lopo safe??

Re: Mother board for tigar that’s Lopo safe??

Re: Mother board for tigar that’s Lopo safe??

Re: Mother board for tigar that’s Lopo safe??

Re: Mother board for tigar that’s Lopo safe??

Re: Mother board for tigar that’s Lopo safe??