"Tiger 1 Metal Rear Panel"

[jarndice]

I managed to break a mounting lug off of a Tiger 1 rear panel,
Fortunately I had a spare one from an old Heng Long Tiger 1, So now I am just finishing it ready to re-install BUT I am sure that I have seen Tiger 1 rear panels made of Metal somewhere but I cannot find it,
My first thought was "Aeromate" and then "Ludwigs" but I could really do with some help,
It does not need to have any fixtures or fittings because I have that covered.
Shaun.

[jeman]

I'm sure I've seen them on fleebay.......from Canada I think, but they are expensive with the postage !

[john1970]

Mr Forgebear has them on ebay in his shop

[brizo58]

Hi Shaun
There's one on eBay.co.uk £24.95 +post. And yep it's Forgebear he has 5 of them. Brian...

[jarndice]

Brian, Thanks but I have already been in contact with our hero.
shaun.

[john1970]

eBay item number:162110258766

[leopardgreece]

I m making my Torro King Tiger IR metal upper hull stronger

uploadfromtaptalk1466886927437.jpg (45.26 KiB) Viewed 1578 times

uploadfromtaptalk1466886915182.jpg (45.26 KiB) Viewed 1578 times

uploadfromtaptalk1466886900288.jpg (40.73 KiB) Viewed 1578 times

uploadfromtaptalk1466886871483.jpg (37.23 KiB) Viewed 1578 times

uploadfromtaptalk1466886845490.jpg (30.64 KiB) Viewed 1578 times

????? ?? SM-P605 ???????????? Tapatalk

[jarndice]

The Mato Tiger 1 metal rear panel arrived this morning,
Dave (Forgebear)had already PMd me that it was short on the bottom of the panel compared with Heng Long or Taigen,
I have just checked it out against a Taigen panel it is identical including the position of the mounting lugs EXCEPT there is a 2mm shortfall on the bottom and that is not even a challenge,
Thank you Dave and by the way I have just placed------
www.forgebeartanks.com
on my favourites list.
Shaun.

[forgebear]

The Mato Tiger 1 metal rear panel arrived this morning,
Dave (Forgebear)had already PMd me that it was short on the bottom of the panel compared with Heng Long or Taigen,
I have just checked it out against a Taigen panel it is identical including the position of the mounting lugs EXCEPT there is a 2mm shortfall on the bottom and that is not even a challenge,
Thank you Dave and by the way I have just placed------
http://www.forgebeartanks.com
on my favourites list.
Shaun.

thanks for the add prices will not go up and we will still give the same service
dave

[jarndice]

What with my Asiatam Panzer 4 metal hull and the Grandchildren on holiday I have only just applied myself to the Metal back panel supplied as ever very speedily by Dave.
As I mentioned before it needed a length of 3mm brass tube which I soldered onto the base of the back plate and after that it was just a little fettling,
It clearly was not supposed to be fitted onto a Taigen Hull but in future when next I am in the market for another Tiger 1 I will order a metal back plate from Dave at the same time.
Apart from the cost of the Metal panel the only other outlay was an 11.5 cm long x 3mm brass tube, (4) 10mmx3mm countersunk neodymium magnets and a piece of 16cmx2cmx2.5mm plasticard. and a couple of M3 screws and in exchange for a couple of hours working out how to do the fix I now have the peace of mind that the fragile locating tabs on the old plastic back panel are a thing of the past.
Shaun.