OCD Builds.... Research Tanks in 1/35th 8O

[ALPHA]

Here you go my friend



They have HL mounting so they will fit other models m1

Hey thanks Kiaser ....You can delete the link now

ALPHA

[ALPHA]

I will build this puppy it will jump ....... track burns

Challenger 2

I was thinking of using RC car parts

ALPHA

[ALPHA]

that will do

Need to Study a tad more...there was a guy who built his own low ratio gearbox for his Tiger about two or three years ago...He pmed ...me to give me some details...thing is his were super low...the tank could almost go up a vertical incline...not what I'm interested in ...for the M1 ...the need is for speed

ALPHA

[ALPHA]

550 cans should get lift off that is the plan

Mated to 4.1 gears....hard to say...stock 3.1s would fly ...would definitely need to change to steel though

ALPHA

[ALPHA]

Had a chat about that so possible to change to 3:1 , what do you think Alpha step in the right direction For HL upgrading .

I like the in line gear setup and enclosed metal housing full bearings .

I think the gearboxes are sweet...just the gear ratio a little low ...man..if I could put a couple of my High torque Airsoft motors in it...I really think it would tear up the place ....When I did tech work...I hooked one up direct to power ...I swear ..I never heard another motor scream like that ...and it wasn't even a name brand Systema motor...that was slower by far in comparison....thing is those motors run on 12 volt...so not sure there is an RX that can handle

ALPHA

[ALPHA]

Mmm I was thinking the elmod and IBU can run at 11.4v .

Close enough lol................HMM Makes it a rather pricey mod lol

ALPHA

[ALPHA]

FIREFLY UPDATEs:



Spliced in some section of tracks..(suggested by Painless) it was tricky...the new vinyl is different from the old stuff that was on before...it carved away easy enough...but was very heat sensitive ....melted when I put a blow dryer to it ....Live and learn...kept the heat away the second go around

Carpe Diem Gents

ALPHA

[PainlessWolf]

Alpha,
Beautifully done! The splicing is done so well that it looks like one section of track. ;o) No more complaining about doing 1/35 scale stuff. You are better at it than I am by far.
regards,
Painless

[ALPHA]

a hair dry that sensitive to heat, looks the business Alpha , makes the Sherm stand out with extra detail

LOL...............yup...the teeth turned into little nubs ....the timing sucked...because I had the track in the perfect shape ...so it was back to the bench to make another one

ALPHA

[ALPHA]

Alpha,
Beautifully done! The splicing is done so well that it looks like one section of track. ;o) No more complaining about doing 1/35 scale stuff. You are better at it than I am by far.
regards,
Painless

It was dangerous to say the least Painless...had to cut the end pads in half so they would match up..Had to make sure my chisel blade was clean and sharp lol...slipped once...cut my finger a little...lucky it wasn't a gash ....You can kind of still tell as the teeth are slightly different...less detail on the new section...the pads are thicker and the newer vinyl doesn't take paint as well...you can see the section in the second photo...the first one is kind of good lol
These 1/35ths built up are becoming very handy....I took some comparison photos of the Chi Nu and the Firefly ...proved to be surprising...as the Chi Nu is a relatively good sized tank

As far as being better than anyone...I'd say nah to that lol......I'm just trying to slap these together as fast as I can so I can get back to 1/16...especially the Chi Nu ....actually with my fading eyesight...........I'm surprised I got this far

ALPHA