I might be able to scavenge the columns from my Ausf D, I think I have a spare plastic mantlet that I am not planning on using.
Here is the ATAK mantlet that came with the Ausf A
Looking for electronics recommendations
Re: Looking for electronics recommendations
Panther D (WIP)
Panther A (WIP)
Panther G (WIP)
Jagdpanther G2 (WIP)
Tiger II (WIP)
Pz.Kpfw. VIII Maus V2 (WIP)
Pz.Kpfw. II Ausf L (WIP)
Sd.Kfz. 234/2 (WIP)
Leopard 1A1A1 (WIP)
Turm III (WIP)
VK 45.01 (H) (WIP)
Churchill VII (WIP)
Chieftain Mk 3 (WIP)
Panther A (WIP)
Panther G (WIP)
Jagdpanther G2 (WIP)
Tiger II (WIP)
Pz.Kpfw. VIII Maus V2 (WIP)
Pz.Kpfw. II Ausf L (WIP)
Sd.Kfz. 234/2 (WIP)
Leopard 1A1A1 (WIP)
Turm III (WIP)
VK 45.01 (H) (WIP)
Churchill VII (WIP)
Chieftain Mk 3 (WIP)
- HERMAN BIX
- Brigadier
- Posts: 10414
- Joined: Sun Jan 12, 2014 12:15 am
- Location: Gold Coast,Australia
Re: Looking for electronics recommendations
I managed to butcher an H/L inner mantlet section to make the Atak version work on 111.
Might have a spare bit if you get stuck.
As for electronics, I went with H/L 6.1s but these are already hard to find.
Might have a spare bit if you get stuck.
As for electronics, I went with H/L 6.1s but these are already hard to find.
HL JAGDPANTHER,HL TIGER 1,HL PzIII MUNITIONSCHLEPPER, HL KT OCTOPUS,HL PANTHER ZU-FUSS,HL STuG III,HL T34/85 BEDSPRING,
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
-
- Warrant Officer 1st Class
- Posts: 1689
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: Looking for electronics recommendations
I understand better! I did not know this material, learned something, thank you Herman. I allow myself to join the link of your 111 for our friend STHV
viewtopic.php?t=31768
viewtopic.php?t=31768
Re: Looking for electronics recommendations
Thank you!
The speaker is currently on its way and I have the battery ready to go, just need to find some plasticard so I can build some internal supports for the modified upper hull.
Am I correct in saying that Cyano glue is super glue?
The speaker is currently on its way and I have the battery ready to go, just need to find some plasticard so I can build some internal supports for the modified upper hull.
Am I correct in saying that Cyano glue is super glue?
Panther D (WIP)
Panther A (WIP)
Panther G (WIP)
Jagdpanther G2 (WIP)
Tiger II (WIP)
Pz.Kpfw. VIII Maus V2 (WIP)
Pz.Kpfw. II Ausf L (WIP)
Sd.Kfz. 234/2 (WIP)
Leopard 1A1A1 (WIP)
Turm III (WIP)
VK 45.01 (H) (WIP)
Churchill VII (WIP)
Chieftain Mk 3 (WIP)
Panther A (WIP)
Panther G (WIP)
Jagdpanther G2 (WIP)
Tiger II (WIP)
Pz.Kpfw. VIII Maus V2 (WIP)
Pz.Kpfw. II Ausf L (WIP)
Sd.Kfz. 234/2 (WIP)
Leopard 1A1A1 (WIP)
Turm III (WIP)
VK 45.01 (H) (WIP)
Churchill VII (WIP)
Chieftain Mk 3 (WIP)
Re: Looking for electronics recommendations
For mantlet mounting, had you considered the little brass hexagonal motherboard stand off posts? https://www.amazon.co.uk/6-32-Brass-Mot ... B00213KL5I
I used them to mount my mantlet, just screwed them through the backing peice, stuck 2 lumps of miliput on to the back of the Atak mantlet and then pushed it into place on the turret. Once the miliput has set you can unscrew the backing peice, take the mantlet off the turret and reinforce the miliput around the posts.
I used them to mount my mantlet, just screwed them through the backing peice, stuck 2 lumps of miliput on to the back of the Atak mantlet and then pushed it into place on the turret. Once the miliput has set you can unscrew the backing peice, take the mantlet off the turret and reinforce the miliput around the posts.