Thanks Alwyn,
I am currently printing at nozzle 200 and bed 60, standard settings as far as I know.
when it fails it is stringing a lot, tomorrow I will try it again and will make pictures if it goes wrong again,
retraction is on, 8mm and speed 50mm/s, Z-hop is not on.
finally
Re: finally
Regards,
Jaap
Jaap
- AlwynTurner
- 2nd Lieutenant
- Posts: 2600
- Joined: Thu Oct 23, 2014 10:47 am
- Location: Chapel-en-le-Frith, Derbyshire
Re: finally
OK set the z hop to on, check that you have the cooling fan running, if you are using pla try cutting the print head temp to 197, then 195. This may sound silly but check that the screws holding the print head are tight, when I got my cr-10 a lot of the screws weren't tightened and the one I forgot to check was the one holding the hot end was loose and consequently the print quality was awful because the nozzle was wiggling around
If it goes wrong again post some pics
Regards
Alwyn
If it goes wrong again post some pics
Regards
Alwyn
YOU'RE NEVER TOO OLD TO HAVE A HAPPY CHILDHOOD!
Saladin scratchbuild, Matilda scratchbuild, Churchill scratchbuild, Crusader scratchbuild, M10 Achiĺles scratchbuild, Universal Carrier scratchbuild
Saladin scratchbuild, Matilda scratchbuild, Churchill scratchbuild, Crusader scratchbuild, M10 Achiĺles scratchbuild, Universal Carrier scratchbuild
Re: finally
Alwyn,
Thanks, I had to look for Z-hop.
I use ultimaker cura or/and creality cura.
they are basically the same, althoug in ultimakeer i dont have the profile for the Ender 3 max, where creality cura didnt show Z-hop in the settings.
Afer some searching I found where I could switch it on, so I see it in the settings, so switched it on for the slicing.
I am now printing the barrels, which goes ok so far.
After this the next attempt for the jacks.
Thanks, I had to look for Z-hop.
I use ultimaker cura or/and creality cura.
they are basically the same, althoug in ultimakeer i dont have the profile for the Ender 3 max, where creality cura didnt show Z-hop in the settings.
Afer some searching I found where I could switch it on, so I see it in the settings, so switched it on for the slicing.
I am now printing the barrels, which goes ok so far.
After this the next attempt for the jacks.
Regards,
Jaap
Jaap
Re: finally
Yeah, managed to print both jacks without problems, Z-hop did the trick
So, I will continue with the other parts.
In the mean time I also find a very nice detailed version of the nebelwerfer in 58mm, so I upscaled it and that will be the next project, that way I can easily compare them and have a battery of nebelwerfers
So, I will continue with the other parts.
In the mean time I also find a very nice detailed version of the nebelwerfer in 58mm, so I upscaled it and that will be the next project, that way I can easily compare them and have a battery of nebelwerfers
Regards,
Jaap
Jaap
- AlwynTurner
- 2nd Lieutenant
- Posts: 2600
- Joined: Thu Oct 23, 2014 10:47 am
- Location: Chapel-en-le-Frith, Derbyshire
Re: finally
That's great Jee, glad you managed to find the right settings, navigating the CURA settings can be tricky when you are a new learner.
Good luck with your printing projects
Alwyn
Good luck with your printing projects
Alwyn
YOU'RE NEVER TOO OLD TO HAVE A HAPPY CHILDHOOD!
Saladin scratchbuild, Matilda scratchbuild, Churchill scratchbuild, Crusader scratchbuild, M10 Achiĺles scratchbuild, Universal Carrier scratchbuild
Saladin scratchbuild, Matilda scratchbuild, Churchill scratchbuild, Crusader scratchbuild, M10 Achiĺles scratchbuild, Universal Carrier scratchbuild