Page 1 of 3
MATO BARREL SMOKE KIT
Posted: Sat Feb 08, 2025 7:34 am
by HERMAN BIX
Gday folks
By any chance have any of you successfully fitted a MATO barrel smoke system to an H/L 7.1 board??
I have one but for the life of me cannot get it to work.
There is no diagram showing how it needs to go nor are there sufficient bits in the kit I believe.
Any assistance greatly appreciated
Re: MATO BARREL SMOKE KIT
Posted: Sat Feb 08, 2025 9:26 am
by jfulls94
I have exactly the same problem, except I'm trying to use a Taigen smoker unit with a Clark TK50
my issue is "i think" that i don't have enough power going to the unit from my board. I'm not so sure on HL TK boards unfortunately
Sent from my SM-S921B using Tapatalk
Re: MATO BARREL SMOKE KIT
Posted: Sat Feb 08, 2025 1:01 pm
by Jofaur86
Hello Mr.Bix,
Found this, don't know if it will help you? video from Aliexpress, if not do you have photos of your equipment?
Vidéo
https://fr.aliexpress.com/i/1005003035623830.html
Re: MATO BARREL SMOKE KIT
Posted: Sat Feb 08, 2025 1:09 pm
by Jofaur86
Re: MATO BARREL SMOKE KIT
Posted: Sat Feb 08, 2025 1:12 pm
by Jofaur86
Re: MATO BARREL SMOKE KIT
Posted: Sat Feb 08, 2025 1:25 pm
by Jofaur86
jfulls94 wrote: ↑Sat Feb 08, 2025 9:26 am
I have exactly the same problem, except I'm trying to use a Taigen smoker unit with a Clark TK50
my issue is "i think" that i don't have enough power going to the unit from my board. I'm not so sure on HL TK boards unfortunately
Sent from my SM-S921B using Tapatalk
For TK 50
Specification
Parameter
Unit
Maximum current of track ESC, connect motor to on-board connector 20 A
Maximum current of track ESC, connect motor to pads on PCB 60 A
Maximum current of track ESC, A1 variant, connect motor to pads on PCB 105 A
Maximum current of turret and cannon elevation ESC 6 A
Maximum current of Smoker Driver 6A
Maximum supply voltage 11.4 V
Minimum supply voltage 7.2 V
Re: MATO BARREL SMOKE KIT
Posted: Sat Feb 08, 2025 2:14 pm
by jfulls94
Jofaur86 wrote:jfulls94 wrote: ↑Sat Feb 08, 2025 9:26 am
I have exactly the same problem, except I'm trying to use a Taigen smoker unit with a Clark TK50
my issue is "i think" that i don't have enough power going to the unit from my board. I'm not so sure on HL TK boards unfortunately
Sent from my SM-S921B using Tapatalk
For TK 50
Specification
Parameter
Unit
Maximum current of track ESC, connect motor to on-board connector 20 A
Maximum current of track ESC, connect motor to pads on PCB 60 A
Maximum current of track ESC, A1 variant, connect motor to pads on PCB 105 A
Maximum current of turret and cannon elevation ESC 6 A
Maximum current of Smoker Driver 6A
Maximum supply voltage 11.4 V
Minimum supply voltage 7.2 V
Brilliant thank you sorry for Hijacking the thread Herman!
Sent from my SM-S921B using Tapatalk
Re: MATO BARREL SMOKE KIT
Posted: Sat Feb 08, 2025 8:10 pm
by Jofaur86
Re: MATO BARREL SMOKE KIT
Posted: Sat Feb 08, 2025 11:51 pm
by HERMAN BIX
No Hijacking at all mate, we all have problems to solve & wherever that solution comes from, its good !
Re: MATO BARREL SMOKE KIT
Posted: Tue Feb 11, 2025 4:56 am
by HERMAN BIX
Still no joy on this.
The Mato system which is all thats available down here didnt come with a flash bulb & cable.
It does however need to use one side of the V7.1 board LED1 station to power up the pump so I cant use that to run a flash from.
The Mato set up has a small sub board but noting is marked and I cannot find anything online about if any of the ports have a flash function.
If anyone has any ideas I will happily try them
Cheers
