heya guys...
just in case someona has a claver mind thant myselft at this moment...
i've two elmods pro rev E in my tanks, they work great, but i haven't connected them to the computer for years, until today
i've tried elmod app v1.06 and v10, but no joy, they seems to not see the boards. I've tried with two diferent computers, same result. I do not remember whar firmare are loaded on the boards.
i've tried the old elmod configurator, but it do not wont start in my w10 computer. The last time i eas able to hook them up was in my old w7 computer,,,
any ideas?
i forgot.. i use the usb cable that came with the elmod boards...
best regards
Elmod App not recognizing TWO elmods...
Elmod App not recognizing TWO elmods...
Jussek
https://www.facebook.com/pages/Club-RC-Reus-Secci%C3%B3-de-Modelisme-Militar-Radiocontrolat-PzGr-Tarraco/639220812799552
https://www.facebook.com/pages/Club-RC-Reus-Secci%C3%B3-de-Modelisme-Militar-Radiocontrolat-PzGr-Tarraco/639220812799552
Re: Elmod App not recognizing TWO elmods...
Hi Jussek,Jussek wrote:heya guys...
just in case someona has a claver mind thant myselft at this moment...
i've two elmods pro rev E in my tanks, they work great, but i haven't connected them to the computer for years, until today
i've tried elmod app v1.06 and v10, but no joy, they seems to not see the boards. I've tried with two diferent computers, same result. I do not remember whar firmare are loaded on the boards.
i've tried the old elmod configurator, but it do not wont start in my w10 computer. The last time i eas able to hook them up was in my old w7 computer,,,
any ideas?
i forgot.. i use the usb cable that came with the elmod boards...
best regards
I had the same problem months back. You need to download the latest FW to the board before you'll be able to access the board with the latest app.
Barry
"Details make perfection, and perfection is not a detail."
Leonardo Da Vinci
Leonardo Da Vinci
Re: Elmod App not recognizing TWO elmods...
thanks Barry
i was looking at this too, but i've been unable to find the firmware on the elmod web, reading the manual it seems that you can only update it through the software:
Firmware update
For updating the firmware the ElMod Fusion must be connected to a computer. To set the PCB in update mode, switch off the voltage
and press and hold the setup pushbutton on the ElMod Fusion. Switch the voltage on again. The blue status LED blinks three times.
Now start the configuration software and press the red "Update" button. Follow the instruction. on the screen.
The newest firmware versions are always included in the current installation package of the configuration software. A new version of
the configuration software may be installed anytime. It's not necessary to deinstall the existing version before.
here is my main concern... because the elmod app is not recognizing the boards, so i'm afraid to finish with an unusable card if the app is not connecting to it
maybe i'm doing something wrong...
i was looking at this too, but i've been unable to find the firmware on the elmod web, reading the manual it seems that you can only update it through the software:
Firmware update
For updating the firmware the ElMod Fusion must be connected to a computer. To set the PCB in update mode, switch off the voltage
and press and hold the setup pushbutton on the ElMod Fusion. Switch the voltage on again. The blue status LED blinks three times.
Now start the configuration software and press the red "Update" button. Follow the instruction. on the screen.
The newest firmware versions are always included in the current installation package of the configuration software. A new version of
the configuration software may be installed anytime. It's not necessary to deinstall the existing version before.
here is my main concern... because the elmod app is not recognizing the boards, so i'm afraid to finish with an unusable card if the app is not connecting to it
maybe i'm doing something wrong...
Jussek
https://www.facebook.com/pages/Club-RC-Reus-Secci%C3%B3-de-Modelisme-Militar-Radiocontrolat-PzGr-Tarraco/639220812799552
https://www.facebook.com/pages/Club-RC-Reus-Secci%C3%B3-de-Modelisme-Militar-Radiocontrolat-PzGr-Tarraco/639220812799552
Re: Elmod App not recognizing TWO elmods...
heya guys
seems sorted
finally i've been able to install the old configurator software, with the java 1.6 (not the latest 1. and the the soft started up correctly, but was unable to read te card, keep saying that the board had an unknown fw version....
so i unsistalled the app v.10, unsistalled the drivers too, and reisntalled the drivers for the app 1.6, and then the boards were seen again. I just upgraded both to fw v 2.02C, i dont nkow why this is the last version available for this app 1.6...
next step will be install the new app v1.10 and see if then it will be able to upgrade the boards to the last fw
thanks guys!
best regards
seems sorted
finally i've been able to install the old configurator software, with the java 1.6 (not the latest 1. and the the soft started up correctly, but was unable to read te card, keep saying that the board had an unknown fw version....
so i unsistalled the app v.10, unsistalled the drivers too, and reisntalled the drivers for the app 1.6, and then the boards were seen again. I just upgraded both to fw v 2.02C, i dont nkow why this is the last version available for this app 1.6...
next step will be install the new app v1.10 and see if then it will be able to upgrade the boards to the last fw
thanks guys!
best regards
Jussek
https://www.facebook.com/pages/Club-RC-Reus-Secci%C3%B3-de-Modelisme-Militar-Radiocontrolat-PzGr-Tarraco/639220812799552
https://www.facebook.com/pages/Club-RC-Reus-Secci%C3%B3-de-Modelisme-Militar-Radiocontrolat-PzGr-Tarraco/639220812799552
-
- Warrant Officer 1st Class
- Posts: 1665
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: Elmod App not recognizing TWO elmods...
Hello'
not sure if can help? but this in my files, so in case, maybe find ?? the solution. Seems that depending on the version of the cards (shown above) are not all possible to update?
https://elmod.eu/manuals/?lang=en
https://elmod.eu/manuals/?lang=en#archiv
not sure if can help? but this in my files, so in case, maybe find ?? the solution. Seems that depending on the version of the cards (shown above) are not all possible to update?
https://elmod.eu/manuals/?lang=en
https://elmod.eu/manuals/?lang=en#archiv
Re: Elmod App not recognizing TWO elmods...
thanks mate, i already have acces to the manuals, this was not the issue. but all was sorted out now, at least with the app v1.06Jofaur86 wrote: Hello'
not sure if can help? but this in my files, so in case, maybe find ?? the solution. Seems that depending on the version of the cards (shown above) are not all possible to update?
https://elmod.eu/manuals/?lang=en
https://elmod.eu/manuals/?lang=en#archiv
i'm working in the servo parameters for the recoil now, once I have finished I will install the latest version of the app, and the firmware
best regards
Jussek
https://www.facebook.com/pages/Club-RC-Reus-Secci%C3%B3-de-Modelisme-Militar-Radiocontrolat-PzGr-Tarraco/639220812799552
https://www.facebook.com/pages/Club-RC-Reus-Secci%C3%B3-de-Modelisme-Militar-Radiocontrolat-PzGr-Tarraco/639220812799552