Israeli Centurion - Sho’t Kal C (Gimel) - IDF 1980s - Build

c.rainford73 · Post by **c.rainford73** » Mon Apr 29, 2019 1:03 am

Louis exceptional work, this may be my favorite one yet!

The hardware and details are very well designed and look excellent

Panzerjaeger66 · Post by **Panzerjaeger66** » Mon Apr 29, 2019 12:00 pm

wow, you detailing is fantastic!!
I wouldn't have the time and skill....

Ad Lav · Post by **Ad Lav** » Mon Apr 29, 2019 2:57 pm

Amazing work as usual Louis

lmcq11 · Post by **lmcq11** » Mon Apr 29, 2019 5:39 pm

Thank you all for your encouragements.

Panzerjaeger66 wrote:wow, you detailing is fantastic!!I wouldn't have the time and skill...

Good base model. I wish I could have used or reused the hull bins you designed for the kit but these are the Mark II and early Mark III with top opening doors. Late Mark III and up have variations of the side opening doors in either 2 or 3 sections, the Israeli ones have the two sections plus a small bin at the rear right. Looking forward for the kit suspension to be started soon.

: Ludwigs Centurion hull bins

Regards, Louis

Panzerjaeger66 · Post by **Panzerjaeger66** » Mon Apr 29, 2019 9:05 pm

Chris got the data to manufacture all necessary parts for the Sho´t conversion (motor deck, hull backside, stowage bins, filters,...) but after all I´ve seen, you did a much better job than me

Post by **Son of a gun-ner** » Tue Apr 30, 2019 12:58 am

Gosh, this is a work of art Louis, bravo sir

lmcq11 · Post by **lmcq11** » Sun May 05, 2019 11:54 pm

Hi,

Presenting the 1/16 Centurion suspension and road wheels, a modelling task you probably only want to do once in your life.

As seen in the book "Centurion tanks of the IDF Vol 1", the Centurion has 3 Horstman double bogie suspension modules on each side.

: 1/16 RC Centurion Shot Kar Gimel tank

The central unit does not have shock absorbers on either side.

: 1/16 RC Centurion Shot Kar Gimel tank

Details of the shock absorbers oil container. I have seen two variants of the cap for the oil, the modeller needs to select one for his tank.

: 1/16 RC Centurion Shot Kar Gimel tank

Schematics were very useful to understand the working and main components of the suspension units, making the build a lot more interesting and needed for avoiding mistakes. Plus you should be adding scratch build details to it.

: 1/16 RC Centurion Shot Kar Gimel tank

: 1/16 RC Centurion Shot Kar Gimel tank

Parts are assembled for the first unit. I was happy to see that Panzerjaeger66 reproduced the main components quite accurately. This is important to me because my style is to build RC tanks but also accurate models that can also sustain close up analysis and pictures, and be a good looking model when on the shelve. I have been waiting for a long time to have a 1/16 Centurion so I won't cut corners.

: 1/16 RC Centurion Shot Kar Gimel tank

My parts had a defect. The critical plate that covers the front of the suspension were not created equal, a manufacturing issue. Some were as they should be, while others we're thick and devoid of much detail. There were a few spares provided so I was able to make 6 that look ok through scratching, sanding and polishing.

: 1/16 RC Centurion Shot Kar Gimel tank

This is the suspension cover part as it should be before rounding the tip as per instructions. Proper preparation and handling of these parts might decide the fate of your build, specially for the first one because you do not have experienced it yet. If this part is too thick, it will not bend easily, will likely crack and will not fit the slot it needs to go into. Do this while you have superglue all over your fingers and things will become ugly real fast. Make it too thin and it will bulge, might also crack because it is too weak, won't look good and won't be solid.

: 1/16 RC Centurion Shot Kar Gimel tank

The part is put into hot water in order to smoothen the plastic so that it does not break while bending it.

: 1/16 RC Centurion Shot Kar Gimel tank; Capture9.JPG (94.99 KiB) Viewed 2331 times

Slowly apply gentle pressures in steps and with increasing force to bend the part around a round object to make it soft.

: 1/16 RC Centurion Shot Kar Gimel tank

Continuing on following post.

lmcq11 · Post by **lmcq11** » Mon May 06, 2019 12:15 am

Sub modules are ready for the main operation of assembling the suspension unit core. This is likely the most technical operation of the build. Superglue is used.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

The tip will need to be folded by about 50% to fit the slot of the side parts. Dry fitting is essential for success. Failure is not an option. the tip was slowly bended and one side was inserted at a time, left, right, back.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

After success with the first module, an assembly chain is created.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

The main body of the 6 suspension modules are done. It is a load off.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

Next task is to build the suspension arms.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

It is not entirely clear how the 2 metal components of each arm need to be assembled together. I was lucky to have M2.5 brass bolts on hand, they fit perfectly.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

Another chain is created for the suspension arms assembly, as per instructions. This takes hours.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

Assembly of the arms into the core module.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

They work quite well and require few adjustments.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

Continuing on following post.

lmcq11 · Post by **lmcq11** » Mon May 06, 2019 12:26 am

The 6 modules after step 2. Gone outside to enjoy the nice spring weather while continuing the build.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

The shock absorbers were installed on the modules. They move freely and are solid, I have no worries they will break.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

Added details as per reference picture, such a Meng nuts and the oil fill caps.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build; Capture22.JPG (99.95 KiB) Viewed 2488 times

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

Last step is to install the road wheels. These are the parts that I required, in sequence.

: 1/16 RC Centurion Tank Shot Kal Gimel IDF build

The main bolt needed to be cut so that another bolt can be screwed from the other side to hold the shaft on the suspension arm. This is not very difficult, it just takes time and a lot of part preparations.