Page 1 of 2
TK60 non Sbus help
Posted: Tue Aug 14, 2018 7:24 pm
by 68firebird
Purchased a tk60 and flysky is16s and 10ch as per clark setup.bound tx to rx and plugged in ch1-8 as per instrutions.assiged chrysler 7and 8 to switches.set trims to centre 50%.nothing.please any suggestions.
Many thanks
Re: TK60 non Sbus help
Posted: Tue Aug 14, 2018 7:29 pm
by c.rainford73
68firebird wrote:Purchased a tk60 and flysky is16s and 10ch as per clark setup.bound tx to rx and plugged in ch1-8 as per instrutions.assiged chrysler 7and 8 to switches.set trims to centre 50%.nothing.please any suggestions.
Many thanks
What's happening with your setup? More details please
Re: TK60 non Sbus help
Posted: Tue Aug 14, 2018 7:37 pm
by 68firebird
Turn on power and rx red light comes on.shift switches to start engine
No sound shift switch to engage clutch.no motion from motors. I don't have a volume knob connected to board and upper hull and smoker not connected.
Re: TK60 non Sbus help
Posted: Tue Aug 14, 2018 7:38 pm
by c.rainford73
68firebird wrote:Turn on power and rx red light comes on.shift switches to start engine
No sound shift switch to engage clutch.no motion from motors. I don't have a volume knob connected to board and upper hull and smoker not connected.
You must have a volume knob for sound.
Re: TK60 non Sbus help
Posted: Tue Aug 14, 2018 8:00 pm
by 68firebird
Ok thanks I'll find a volume knob.does everything have to be plugged I to board or can you plug one item at a time.
Re: TK60 non Sbus help
Posted: Tue Aug 14, 2018 8:03 pm
by c.rainford73
68firebird wrote:Ok thanks I'll find a volume knob.does everything have to be plugged I to board or can you plug one item at a time.
Not necessarily, but the primary connections like power, speaker and volume pot need to be connected. Or all at one time. Hope this helps.
Re: TK60 non Sbus help
Posted: Tue Aug 14, 2018 8:12 pm
by maxmekker
68firebird wrote:Purchased a tk60 and flysky is16s and 10ch as per clark setup.bound tx to rx and plugged in ch1-8 as per instrutions.assiged chrysler 7and 8 to switches.set trims to centre 50%.nothing.please any suggestions.
Many thanks
did you get any info on how to setup/ program the radio etch upon purchace ?
dont forget to put a jumper in the SW port
this might help you
Re: TK60 non Sbus help
Posted: Tue Aug 14, 2018 8:32 pm
by 68firebird
I've put a jumper in the switch port.power is supplied from main battery on off.
Re: TK60 non Sbus help
Posted: Wed Aug 15, 2018 8:49 am
by maxmekker
Any progress ?
Re: TK60 non Sbus help
Posted: Sun Aug 19, 2018 10:30 pm
by 68firebird
I've watched the video and have had some success as in I now have some sound and forward and reverse.have not fitted the top deck and turrett.the rotary dials do what there supposed to do and switches B and C kind of do what there supposed to do as in STOP start and neutral and I can rev the motor.when I engage gear I only have forward and reverse.in the video it says assign channels 5&6.but on the clark website for non s bus these rant used on the 10ch rx.ive plugged into the rx chrysler 1to4 and 789and10
Any idea as please