Page 9 of 11

Re: Coolbank/Tongde M5A1 Stuart /Crusader mk III

Posted: Wed Sep 11, 2024 6:02 pm
by JohnWhyte
Looks good might want to pull the gun out so it's the full length

Re: Coolbank/Tongde M5A1 Stuart /Crusader mk III

Posted: Wed Sep 11, 2024 7:21 pm
by ColemanCollector
JohnWhyte wrote: Wed Sep 11, 2024 6:02 pm Looks good might want to pull the gun out so it's the full length
2tvw3ugm4bs71.jpg
2tvw3ugm4bs71.jpg (197.17 KiB) Viewed 2887 times
Mike.

Re: Coolbank/Tongde M5A1 Stuart /Crusader mk III

Posted: Thu Sep 12, 2024 2:16 am
by Herr Dr. Professor
Do I detect some in-you-end, OH?

Re: Coolbank/Tongde M5A1 Stuart /Crusader mk III

Posted: Fri Sep 13, 2024 3:06 am
by Herr Dr. Professor
JohnWhyte I had been wondering why the gun recoil was but a tiny twitch. Good grief, how dumb can I be? :eh:

Re: Coolbank/Tongde M5A1 Stuart /Crusader mk III

Posted: Fri Sep 13, 2024 11:13 am
by RobW
Quite a few of the early ones shipped like that. It's only obvious when you open up the turret, or read comments in one of the threads on here....

Re: Coolbank/Tongde M5A1 Stuart /Crusader mk III

Posted: Fri Sep 13, 2024 3:01 pm
by Herr Dr. Professor
Right, RobW, I opened the hull, but never the turret, except to peek in from the hatches on top. I did not see the inner end of the barrel until you alerted me. Then I peeked from behind the hatches and saw that half of the gun was depressed inside. I did notice that the elevation and recoil use servos, so I am hoping that Coolbank has a versatile MFU system and will learn more in development of AFVs. Slow down; make just a little more noise; suit hardware to its visual effect, too.

Re: Coolbank/Tongde M5A1 Stuart /Crusader mk III

Posted: Sat Oct 26, 2024 9:20 pm
by MonsieurTox
With all those Stuart out, was someone able to correct the look of the suspension arms? They should be more compressed (more in a straight line than like an inverted "V"). It looks pretty easy to correct the stance but that may lead to some other problems (chassis too close to the ground etc).

Re: Coolbank/Tongde M5A1 Stuart /Crusader mk III

Posted: Mon Jan 27, 2025 9:49 pm
by Redballrunner73
Nice Stuart! love the paint job :thumbup: . I gave in and treated myself to one of these M5'S from HAYA and love it! got some parts from Forgebears and used a bit of artistic licence/historical innacuracy and Voila! (my Stepdads father Alec Herron was a DR but I've only seen these markings on an M3 so apologies if inaccurate :{ ) only issue i have is when turning to the right the engine rev up sound doesn't kick in till halfway through the turn? had to remove a link from each side too to stop tracks binding, but all good now... Brilliant wee Tank for the price what with 3 servo's, recoil + flash + the dual drive...yeah is a wee bitty fast but then it was used a re-con vehicle so all good for hasty retreats from those pesky Tigers and Panthers! @)

...and it looks so Teeny Weeny next to My Challenger 2 (Hi Grandpa! :haha: )

Re: Coolbank/Tongde M5A1 Stuart /Crusader mk III

Posted: Tue Jan 28, 2025 4:48 am
by Redballrunner73
Only thing to find now is where the spotlight plugs into on the board(s) to utilise this function via the 'K' button as per manual? :think:

Re: Coolbank/Tongde M5A1 Stuart /Crusader mk III

Posted: Wed Jan 29, 2025 10:21 pm
by Exhibitedbrute
What searchlight