Page 2 of 3

Re: TORRO RX18 binding

Posted: Sun Jun 20, 2021 5:55 pm
by Jofaur86
when you try to link the TX with the RX? is there the Beier module? or are you testing only TX / RX 18?

Re: TORRO RX18 binding

Posted: Sun Jun 20, 2021 6:07 pm
by Jofaur86
after viewing your videos, it seems to me? that you do not perform the procedure in order? indeed the two inter must be towards the rear, before switching on the TX, and on the attached link it is the left inter that is activated? now i'm trying to figure out what's going on and can be wrong :'(
My English is not good (google translation) and I apologize if some words are changed :eh:

Re: TORRO RX18 binding

Posted: Sun Jun 20, 2021 6:20 pm
by Jofaur86
when you try to link the TX with the RX? is there the Beier module? or are you testing only TX / RX 18?

Re: TORRO RX18 binding

Posted: Sun Jun 20, 2021 6:25 pm
by Jofaur86

Re: TORRO RX18 binding

Posted: Mon Jun 21, 2021 3:01 pm
by kintaroukinji
Jofaur86 wrote:oops? here is the link, but in French where did I find the procedure?
https://www.rc-panzershop.fr/ekmps/shop ... /hl2.4.pdf
I know this binding procedure. I tried binding this way.

Re: TORRO RX18 binding

Posted: Mon Jun 21, 2021 3:23 pm
by Jarlath
Jofaur86 wrote::D Binder Rx and TX,
1: tank and radio powered off
2: interlocking starter and machine gun, pushed to the rear
3: Shoot the inter-machine gun towards you (top left on radio)
4: turn on the radio, the red led of the radio flashes
5: Turn on the tank, the red led flashes faster.Wait 1 minute
6: turn off the tank then the radio
in this order
7: push the inter back, it should work
I thought that MG lever/switch was top right of radio on the V1?

Re: TORRO RX18 binding

Posted: Mon Jun 21, 2021 4:55 pm
by Jofaur86
Bonjour Jarlath :)
Hello, I admit that I no longer know? but it seems that depending on the type of transmitters ?? there are the two solutions, personally I'm talking about the one I have, after seeing if the last generations are different?

Re: TORRO RX18 binding

Posted: Mon Jun 21, 2021 7:35 pm
by Jarlath
Jofaur86 wrote:Bonjour Jarlath :)
Hello, I admit that I no longer know? but it seems that depending on the type of transmitters ?? there are the two solutions, personally I'm talking about the one I have, after seeing if the last generations are different?
V1 Binding procedure right from Taigen manuals.

Re: TORRO RX18 binding

Posted: Mon Jun 21, 2021 7:48 pm
by Jarlath
If you do not have a button on the upper right shoulder, you have a V1 Torro/Taigen 2.4Ghz transmitter.

If you do have the button, then you are at the V2 controller that has a slightly different bind sequence.

Re: TORRO RX18 binding

Posted: Tue Jun 22, 2021 4:04 am
by kintaroukinji
Yes, I own TORRO Ver.1. Sound board USM-HL2 can only be used with Ver.1.
Transmitter
Transmitter
A toggle switch for the machine gun and a dial switch for adjusting the left and right drive motors are located on the upper right of the transmitter.