I got this tank commander with a older model Heng long tank.
I really like the detail and pose of this commander compared to the newer Heng Long ones so he's getting promoted to commanding the King Tiger!
The issue is that he's very shiny and hard (but also flexible) plastic. Very similar to old plastic toy soldiers my dad had when he was little.
Also he's got some really badly applied flesh paint which is also shiny and thick looking.
I tried removing it with Carson paint killer but it didn't even touch it.
Can i go straight in and start putting a white acrylic base coat on or should I use some sort of primer? Also how do I deal with the current flesh paint?
Thanks
Sent from my KB2003 using Tapatalk
Tank commander help
- PainlessWolf
- Lieutenant-Colonel
- Posts: 7408
- Joined: Sun Feb 26, 2012 9:09 pm
- Location: Southern Colorado Rocky Mountains
Re: Tank commander help
Good Afternoon,
A lot can be done with the older Heng Long figures. Just takes some extra work as they are nowhere near as sharply defined as even Tamiya figures. Best bet is to lightly buff the whole figure then primer it in a good Tamiya type plastic primer. Then get out your various sizes of brushes and acrylic and oil paints and pick a uniform and set of facial colors and go to work. I'm the guy who created 'Crazy Joe' and have always had more luck with Uniforms than faces but there are some true Masters on the Forum here when it comes to Figures.
regards and following along,
Painless
A lot can be done with the older Heng Long figures. Just takes some extra work as they are nowhere near as sharply defined as even Tamiya figures. Best bet is to lightly buff the whole figure then primer it in a good Tamiya type plastic primer. Then get out your various sizes of brushes and acrylic and oil paints and pick a uniform and set of facial colors and go to work. I'm the guy who created 'Crazy Joe' and have always had more luck with Uniforms than faces but there are some true Masters on the Forum here when it comes to Figures.
regards and following along,
Painless
...Here for the Dawn...
Re: Tank commander help
Ok some plastic primer and very fine wet and dry.
What about removing the existing flesh paint? Maybe it will be ok to go over the top of it but it's thick and has flooded some of the details
Sent from my KB2003 using Tapatalk
What about removing the existing flesh paint? Maybe it will be ok to go over the top of it but it's thick and has flooded some of the details
Sent from my KB2003 using Tapatalk
-
- Lance Corporal
- Posts: 128
- Joined: Thu Jun 17, 2021 5:24 pm
Re: Tank commander help
If it’s been painted in acrylics, you could try soaking it for a few minutes in isopropyl alcohol (rubbing alcohol) or Detol antiseptic disinfectant. It’s something I do for some bits on my N Gauge model railway.
It’s not a guaranteed method, but worth trying.
It’s not a guaranteed method, but worth trying.
‘Experience is the name everyone gives to their mistakes’ - Oscar Wilde
- Estnische
- Warrant Officer 2nd Class
- Posts: 1065
- Joined: Tue Jun 07, 2016 11:52 pm
- Location: Wollongong, Australia
Re: Tank commander help
If isopropyl alcohol doesn't shift it, at your own risk, try brake fluid. Maybe try a hidden corner first in case it turns out to be to 'hot'.
Everything you need to know about figure painting you can learn from Dave Youngquist.
https://www.youtube.com/playlist?list=P ... 2JgGAng1bB
Everything you need to know about figure painting you can learn from Dave Youngquist.
https://www.youtube.com/playlist?list=P ... 2JgGAng1bB
- Herr Dr. Professor
- Lieutenant
- Posts: 3726
- Joined: Mon Apr 22, 2019 10:48 pm
- Location: Southern Wisconsin USA
Re: Tank commander help
Those of us in the MMMA (Make Modeling Mediocre Again) group that meets at my house every Tuesday use full-strength Super Clean to strip model paints:
Your mileage may vary!
Your mileage may vary!