TORRO RX18 binding
Forum rules
If your question is electronics related please post it in one of the relevant boards here: viewforum.php?f=31
If your question is electronics related please post it in one of the relevant boards here: viewforum.php?f=31
-
- Warrant Officer 1st Class
- Posts: 1664
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: TORRO RX18 binding
when you try to link the TX with the RX? is there the Beier module? or are you testing only TX / RX 18?
-
- Warrant Officer 1st Class
- Posts: 1664
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: TORRO RX18 binding
after viewing your videos, it seems to me? that you do not perform the procedure in order? indeed the two inter must be towards the rear, before switching on the TX, and on the attached link it is the left inter that is activated? now i'm trying to figure out what's going on and can be wrong
My English is not good (google translation) and I apologize if some words are changed
My English is not good (google translation) and I apologize if some words are changed
-
- Warrant Officer 1st Class
- Posts: 1664
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: TORRO RX18 binding
when you try to link the TX with the RX? is there the Beier module? or are you testing only TX / RX 18?
-
- Lance Corporal
- Posts: 156
- Joined: Mon Feb 19, 2018 4:46 am
Re: TORRO RX18 binding
I know this binding procedure. I tried binding this way.Jofaur86 wrote:oops? here is the link, but in French where did I find the procedure?
https://www.rc-panzershop.fr/ekmps/shop ... /hl2.4.pdf
Re: TORRO RX18 binding
I thought that MG lever/switch was top right of radio on the V1?Jofaur86 wrote: Binder Rx and TX,
1: tank and radio powered off
2: interlocking starter and machine gun, pushed to the rear
3: Shoot the inter-machine gun towards you (top left on radio)
4: turn on the radio, the red led of the radio flashes
5: Turn on the tank, the red led flashes faster.Wait 1 minute
6: turn off the tank then the radio
in this order
7: push the inter back, it should work
-
- Warrant Officer 1st Class
- Posts: 1664
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: TORRO RX18 binding
Bonjour Jarlath
Hello, I admit that I no longer know? but it seems that depending on the type of transmitters ?? there are the two solutions, personally I'm talking about the one I have, after seeing if the last generations are different?
Hello, I admit that I no longer know? but it seems that depending on the type of transmitters ?? there are the two solutions, personally I'm talking about the one I have, after seeing if the last generations are different?
Re: TORRO RX18 binding
V1 Binding procedure right from Taigen manuals.Jofaur86 wrote:Bonjour Jarlath
Hello, I admit that I no longer know? but it seems that depending on the type of transmitters ?? there are the two solutions, personally I'm talking about the one I have, after seeing if the last generations are different?
- Attachments
-
[The extension pdf has been deactivated and can no longer be displayed.]
Re: TORRO RX18 binding
If you do not have a button on the upper right shoulder, you have a V1 Torro/Taigen 2.4Ghz transmitter.
If you do have the button, then you are at the V2 controller that has a slightly different bind sequence.
If you do have the button, then you are at the V2 controller that has a slightly different bind sequence.
-
- Lance Corporal
- Posts: 156
- Joined: Mon Feb 19, 2018 4:46 am
Re: TORRO RX18 binding
Yes, I own TORRO Ver.1. Sound board USM-HL2 can only be used with Ver.1.
A toggle switch for the machine gun and a dial switch for adjusting the left and right drive motors are located on the upper right of the transmitter.