Problems with Heng Long Jagdpanther (PARTIALLY SOLVED)

This section is to 'show and tell' about any customizing or re-modeling you have done (or are doing) to a Heng Long tank.
Forum rules
This section is for posting a build log of your Heng Long tank.
Questions relating to issues you are having with your tank(s) should be posted in the General Questions forum here: viewforum.php?f=14
User avatar
Rettinger
Recruit
Posts: 15
Joined: Sun Jul 14, 2019 1:25 pm
Location: Barcelona

Re: Problems with Heng Long Jagdtiger!

Post by Rettinger »

Thanks for your replies!
I have read about the TK-6.0 board that if you plug a cable to the wrong port, may cause a malfunction or a shortcircuit to the board.
Giving that I've plugged and unplugged it many times I am starting to fear the worst: the command board may be actually damaged.

That's why when I assemble everything and I press all ON, the light does not come on and off and nothing responds.
God, I'm starting to hate that board.

Anyway, I am going to assemble the tank again with the stock parts and try to bound it; I hope it works but I certainly know the board is damaged :|
mutt71
Lance Corporal
Posts: 142
Joined: Mon Apr 22, 2019 1:25 am
Location: Clarksville, TN USA

Re: Problems with Heng Long Jagdtiger!

Post by mutt71 »

I understand your frustration as I too am dealing with inexperience in trying to fix issues with my few Tanks. I wish you every success with "awakening" your Tank and enjoying it now and in the future. By following thus thread, I have learned a lot about issues that I am having in my own Tanks. Hang in there my friend, we are all in this together!
HL Snow Leopard Pershing PRO
HL Panzer III X2
HL Panther G
HL Stug IIIG PRO X2
HL Sherman PRO 105
HL Panzer IV
HL King Tiger PRO X2
1/16 DUKW Hull
User avatar
Rettinger
Recruit
Posts: 15
Joined: Sun Jul 14, 2019 1:25 pm
Location: Barcelona

Re: Problems with Heng Long Jagdtiger! (PARTIALLY SOLVED)

Post by Rettinger »

LATEST NEWS:

I tried to bond the stock TK.6-0 command board many times with no result. I can state that this board is oficially dead :'(

I found a cheap RX.18 + controller + speaker and bound cable on a Spanish RC dealer site and I bought it. I have succefully bond the new old RX.18 board (with the controller it came with) and I finally have the Jagdpanther running again!! :) So I partially solved my issues with the Jagdtiger!! Now it's running and it's simply amazing how the new motor, the metal hull and the all metal suspension, wheels and tracks behaves!! It has been worth all the headaches and invested money.

However, this good news are leading to more issues...

THE STOCK PARTS OF MY JADGTIGER ARE FROM A MUCH NEWEST VERSION THAN THE RX.18 BOARD!!!!

Everything from my Tank was designed and manufactured to run with the newest TK.6-0 command board. This means that now with the RX.18 board I bought I downgraded the whole thing and while the tank runs and makes sounds, the smoke unit, elevator, lights and BB system is not compatible thus not working. I feel a bit stupid, but thanks to all this I am learning a lot.

What can I do now? Should I have to buy all the older parts per separate and replace the stock/newer parts with them?
Sub
Sergeant
Posts: 687
Joined: Wed Jul 22, 2009 10:45 am
Location: UK

Re: Problems with Heng Long Jagdtiger! (PARTIALLY SOLVED)

Post by Sub »

Hi.
You could have bought a new TK6.0 board and transmitter from Andrew at HAYA rc tanks.

http://www.hayaltd.co.uk

Go to menu, catagories, accesories general tank parts and its there.

About £60.00 UK pounds.
Give him a ring and he may be able to supply a new TK6.0 board on its own for you....then problem solved.
Sub
User avatar
43rdRecceReg
Major
Posts: 6295
Joined: Fri Jul 31, 2015 11:38 am
Location: North West Highlands, Scotland

Re: Problems with Heng Long Jagdtiger! (PARTIALLY SOLVED)

Post by 43rdRecceReg »

https://www.hayaltd.co.uk/heng_long_24G ... 80723.aspx
Here's a more direct link to the unit Sub mentioned.
Where a measure of interchangeability, or backwards compatibility, was present in some earlier iterations of HL control systems, this is not the case now. Even the 8-pin connectors that link turret functions to the controller can vary.
Thus 'mix and match' configurations are only like to produce frustrating problems. :problem:
On the plus side, your fund of knowledge is building rapidly (like your expenditure :D ) and at the end of it all, you'll have a great looking and well-performing Tank! :thumbup:
"Get your facts first, and then you can distort them as much as you please"- Mark Twain.
User avatar
43rdRecceReg
Major
Posts: 6295
Joined: Fri Jul 31, 2015 11:38 am
Location: North West Highlands, Scotland

Re: Problems with Heng Long Jagdtiger! (PARTIALLY SOLVED)

Post by 43rdRecceReg »

As a footnote to the foregoing, using crimp type bullet connectors to connect the motors to the controller would have been fairly straightforward. A crimping tool and an assortment of connectors can be had online fairly cheaply. They're also fairly easy to use.
This one can be had cheaply on Amazon. Just ensure that the joints are fully insulated, as Sub suggested.
Crimping kit
Crimping kit
Crimping kit.jpg (223.8 KiB) Viewed 3923 times
"Get your facts first, and then you can distort them as much as you please"- Mark Twain.
Jofaur86
Warrant Officer 1st Class
Posts: 1663
Joined: Tue Dec 25, 2018 11:28 pm
Location: Centre France

Re: Problems with Heng Long Jagdtiger! (PARTIALLY SOLVED)

Post by Jofaur86 »

I link that now we will have to resume wiring? To achieve this, you need soldering iron 30/50 watts,
Solder,and thermo sheath for isolated,this seal wiring diagram RX 18 before TK-0.6
35DF325B-F1DB-4DAD-B729-BB0E2AFB1F2A-235-0000002417B63875.jpg
35DF325B-F1DB-4DAD-B729-BB0E2AFB1F2A-235-0000002417B63875.jpg (5.71 KiB) Viewed 3902 times
BEAA01DD-0218-4F40-8D40-9B5AF9DDC389-235-000000248277332A.png
BEAA01DD-0218-4F40-8D40-9B5AF9DDC389-235-000000248277332A.png (233.15 KiB) Viewed 3902 times
D1119927-E04E-414B-BF13-0F0385E8645E-235-00000024E221A6B9.jpg
D1119927-E04E-414B-BF13-0F0385E8645E-235-00000024E221A6B9.jpg (20.96 KiB) Viewed 3902 times
https://www.rc-panzershop.fr/ekmps/shop ... /hl2.4.pdf
User avatar
Son of a gun-ner
Lieutenant-Colonel
Posts: 6865
Joined: Sun May 07, 2017 8:49 pm
Location: Surrey UK

Re: Problems with Heng Long Jagdtiger! (PARTIALLY SOLVED)

Post by Son of a gun-ner »

It was this thread that gave me the idea to post this. . . .

Simple way to connect wires. - RC Tank Warfare
viewtopic.php?f=38&t=28056
Mick - The grit in the underpants of life!
And always happy to spare the bytes

TOTM needs YOU :thumbup: support YOUR TOTM competition, I'm doing my part, are YOU?
Jofaur86
Warrant Officer 1st Class
Posts: 1663
Joined: Tue Dec 25, 2018 11:28 pm
Location: Centre France

Re: Problems with Heng Long Jagdtiger! (PARTIALLY SOLVED)

Post by Jofaur86 »

Principle and color CN 8 wiring Taigen,Heng Long,etc.
IMG_5365.JPG
IMG_5365.JPG (40.93 KiB) Viewed 3895 times
This is the color of the wires of the connecting,cable from CN 8 on RX 18 and the 8 pin plug on the upper châssis ,on which are connected all the motors,rotation,elevation,shot,etc :wave:
Post Reply

Return to “Heng Long Builds”