JagdTiger

This section is for builds that are not strictly Tamiya or Heng Long. For instance, replacing the electronics from a WSN or Matorro, or even a scratch-build.
User avatar
Kostyanchik
Private
Posts: 63
Joined: Wed Dec 13, 2017 3:37 pm
Location: Russia, Moscow

Re: JagdTiger

Post by Kostyanchik »

This design proved to be unreliable and very noisy. Cardan gear collapsed because of very high revs. I refused this design. Nevertheless, I got some experience and began to think how to make the design reliable.

Video of unsuccessful experience
phpBB [video]
using translator
User avatar
Kostyanchik
Private
Posts: 63
Joined: Wed Dec 13, 2017 3:37 pm
Location: Russia, Moscow

Re: JagdTiger

Post by Kostyanchik »

Subsequently, the transmission of the tank was completely replaced with a new one using a bevel gear and a planetary gear. The engines remained the same.
Attachments
SAM_1515.JPG
SAM_1514.JPG
SAM_1508.JPG
SAM_1505.JPG
DSC_1158.JPG
20150215154416.jpg
using translator
User avatar
silversurfer1947
Lieutenant
Posts: 3338
Joined: Tue Oct 27, 2015 9:54 pm
Location: Bristol, UK

Re: JagdTiger

Post by silversurfer1947 »

Speechless! :clap: :clap: :thumbup:
Richard
Tamiya Tiger 1, Taigen FlakPanzer IV,Torro M16 half-track, Tamiya Panther,WSN/Torro T34,Taigen M41 Bulldog,H/l/Taigen Sherman M4A3,H/L T90, Haya M3 Grant, Metal Origins 234/2 Puma, Nashorn by Alwyn. I was only going to have one tank - honest! :D
User avatar
Kostyanchik
Private
Posts: 63
Joined: Wed Dec 13, 2017 3:37 pm
Location: Russia, Moscow

Re: JagdTiger

Post by Kostyanchik »

The use of brushless motors in rc tanks was not the best choice, because the motors have a weak sensitivity. In the end, I chose brushed motors 540. To manage the motors, a board was purchased Tank Control V3.
Now the model has this transmission.

phpBB [video]


phpBB [video]
Attachments
DSC_0003.JPG
DSC_0002.JPG
DSC_1174.JPG
using translator
User avatar
c.rainford73
Major
Posts: 6104
Joined: Thu Aug 25, 2016 7:34 pm
Location: Connecticut USA

Re: JagdTiger

Post by c.rainford73 »

Engineering masterpiece
Tanks alot.... :wave:
User avatar
Kostyanchik
Private
Posts: 63
Joined: Wed Dec 13, 2017 3:37 pm
Location: Russia, Moscow

Re: JagdTiger

Post by Kostyanchik »

From Christian Ludwig ordered a set of uper hull KIT and some accessories
Attachments
20150516190322.jpg
20150516190818.jpg
20150516191930.jpg
20150516190905.jpg
20150516192356.jpg
20150516192651.jpg
20150516192816.jpg
20150516193040.jpg
using translator
User avatar
Kostyanchik
Private
Posts: 63
Joined: Wed Dec 13, 2017 3:37 pm
Location: Russia, Moscow

Re: JagdTiger

Post by Kostyanchik »

Preliminary fitting of parts
Attachments
20150517112650.jpg
20150517112140.jpg
20150517112011.jpg
20150517112105.jpg
20150517112034.jpg
20150517111909.jpg
20150517111941.jpg
using translator
User avatar
43rdRecceReg
Major
Posts: 6295
Joined: Fri Jul 31, 2015 11:38 am
Location: North West Highlands, Scotland

Re: JagdTiger

Post by 43rdRecceReg »

My jaw almost hit the floor, when I saw those drive shafts with inboard and outboard constant velocity joints (Universal couplings) :O That's a drive train I've not seen in a model tank before. 8O In most WW2 tanks a propellor shaft ran from the engine in the back to the differential at the front. Your arrangement is beginning to hint at that.. Truly knocked out by the level of engineering excellence here. :clap:
A question, though, K., will you put a deck above the drive shafts to provide a mounting plate for the MFU and other components?
"Get your facts first, and then you can distort them as much as you please"- Mark Twain.
User avatar
Kostyanchik
Private
Posts: 63
Joined: Wed Dec 13, 2017 3:37 pm
Location: Russia, Moscow

Re: JagdTiger

Post by Kostyanchik »

Thank you all for your interest!

I plan to place the elements as follows: a speaker at the rear of the tank behind the engines; battery in the center between the motors; control board in front of the bevel gears.
using translator
User avatar
Kostyanchik
Private
Posts: 63
Joined: Wed Dec 13, 2017 3:37 pm
Location: Russia, Moscow

Re: JagdTiger

Post by Kostyanchik »

Fastened the rear traction loops and installed the rear plate
Attachments
20150517173205.jpg
20150517173134.jpg
20150517173316.jpg
20150517173234.jpg
20150517154623.jpg
20150517154605.jpg
20150517153333.jpg
20150517151112.jpg
using translator
Post Reply

Return to “Other Builds”