JagdTiger
- Kostyanchik
- Private
- Posts: 63
- Joined: Wed Dec 13, 2017 3:37 pm
- Location: Russia, Moscow
Re: JagdTiger
This design proved to be unreliable and very noisy. Cardan gear collapsed because of very high revs. I refused this design. Nevertheless, I got some experience and began to think how to make the design reliable.
Video of unsuccessful experience
Video of unsuccessful experience
using translator
- Kostyanchik
- Private
- Posts: 63
- Joined: Wed Dec 13, 2017 3:37 pm
- Location: Russia, Moscow
Re: JagdTiger
Subsequently, the transmission of the tank was completely replaced with a new one using a bevel gear and a planetary gear. The engines remained the same.
using translator
- silversurfer1947
- Lieutenant
- Posts: 3338
- Joined: Tue Oct 27, 2015 9:54 pm
- Location: Bristol, UK
Re: JagdTiger
Speechless!
Richard
Tamiya Tiger 1, Taigen FlakPanzer IV,Torro M16 half-track, Tamiya Panther,WSN/Torro T34,Taigen M41 Bulldog,H/l/Taigen Sherman M4A3,H/L T90, Haya M3 Grant, Metal Origins 234/2 Puma, Nashorn by Alwyn. I was only going to have one tank - honest!
Tamiya Tiger 1, Taigen FlakPanzer IV,Torro M16 half-track, Tamiya Panther,WSN/Torro T34,Taigen M41 Bulldog,H/l/Taigen Sherman M4A3,H/L T90, Haya M3 Grant, Metal Origins 234/2 Puma, Nashorn by Alwyn. I was only going to have one tank - honest!
- Kostyanchik
- Private
- Posts: 63
- Joined: Wed Dec 13, 2017 3:37 pm
- Location: Russia, Moscow
Re: JagdTiger
The use of brushless motors in rc tanks was not the best choice, because the motors have a weak sensitivity. In the end, I chose brushed motors 540. To manage the motors, a board was purchased Tank Control V3.
Now the model has this transmission.
Now the model has this transmission.
using translator
- c.rainford73
- Major
- Posts: 6104
- Joined: Thu Aug 25, 2016 7:34 pm
- Location: Connecticut USA
- Kostyanchik
- Private
- Posts: 63
- Joined: Wed Dec 13, 2017 3:37 pm
- Location: Russia, Moscow
Re: JagdTiger
From Christian Ludwig ordered a set of uper hull KIT and some accessories
using translator
- Kostyanchik
- Private
- Posts: 63
- Joined: Wed Dec 13, 2017 3:37 pm
- Location: Russia, Moscow
- 43rdRecceReg
- Major
- Posts: 6294
- Joined: Fri Jul 31, 2015 11:38 am
- Location: North West Highlands, Scotland
Re: JagdTiger
My jaw almost hit the floor, when I saw those drive shafts with inboard and outboard constant velocity joints (Universal couplings) That's a drive train I've not seen in a model tank before. In most WW2 tanks a propellor shaft ran from the engine in the back to the differential at the front. Your arrangement is beginning to hint at that.. Truly knocked out by the level of engineering excellence here.
A question, though, K., will you put a deck above the drive shafts to provide a mounting plate for the MFU and other components?
A question, though, K., will you put a deck above the drive shafts to provide a mounting plate for the MFU and other components?
"Get your facts first, and then you can distort them as much as you please"- Mark Twain.
- Kostyanchik
- Private
- Posts: 63
- Joined: Wed Dec 13, 2017 3:37 pm
- Location: Russia, Moscow
Re: JagdTiger
Thank you all for your interest!
I plan to place the elements as follows: a speaker at the rear of the tank behind the engines; battery in the center between the motors; control board in front of the bevel gears.
I plan to place the elements as follows: a speaker at the rear of the tank behind the engines; battery in the center between the motors; control board in front of the bevel gears.
using translator
- Kostyanchik
- Private
- Posts: 63
- Joined: Wed Dec 13, 2017 3:37 pm
- Location: Russia, Moscow