Jadgpanzer L70/V Build

This section is for builds that are not strictly Tamiya or Heng Long. For instance, replacing the electronics from a WSN or Matorro, or even a scratch-build.
User avatar
dgsselkirk
Warrant Officer 2nd Class
Posts: 1484
Joined: Tue Oct 16, 2012 1:57 am
Location: Kitchener, Ontario, Canada
Contact:

Jadgpanzer L70/V Build

Post by dgsselkirk »

Greetings Guys!

I haven't posted a build on here since my KT and I will not be going into that depth again! :haha:

So I will give basic outlines and let the pictures speak for themselves. I am no master and do not pretend to be. I try and do things the easiest, fastest, and cheapest way possible. That being said I did splurge on this one a bit. I had an HL Mk. IV that drove well but the turret set up and recoil was driving me crazy! Kept konking out and finally the elevation on the Clark board blew out so I decided to hell with it, scrap it and build an L70! So I broke down and bought from panzerparts his L70 kit for I think reasonable 109 euros. Less expensive than Profiline who we now have to wait to see their kits again. Panzerparts also comes with more metal detail pieces than resin that Profiline including a barrel which I did not use but more on that later! Here are the first hull reconstruction pics. As always I gutted the battery box and fill the lower hull with tough as steel resin. Also bought the metal drive covers with bearings from Panzerparts and they were really reasonable I thought. Mounted them and test fitted the engines and shafts...
Attachments
L70 build 9.jpg
L70 build 9.jpg (46.18 KiB) Viewed 5567 times
L70 build 8.jpg
L70 build 8.jpg (68.24 KiB) Viewed 5567 times
L70 build 7.jpg
L70 build 7.jpg (41.38 KiB) Viewed 5567 times
L70 build 6.jpg
L70 build 6.jpg (57.18 KiB) Viewed 5567 times
L70 build 5.jpg
L70 build 5.jpg (41.61 KiB) Viewed 5567 times
L70 build 4.jpg
L70 build 4.jpg (46.74 KiB) Viewed 5567 times
L70 build 3.jpg
L70 build 3.jpg (46.09 KiB) Viewed 5567 times
L70 build 2.jpg
L70 build 2.jpg (45.02 KiB) Viewed 5567 times
L70 build 1.jpg
L70 build 1.jpg (55.59 KiB) Viewed 5567 times
"There are things in Russia which are not as they seem..."
Georgy Konstantinovich Zhukov
User avatar
dgsselkirk
Warrant Officer 2nd Class
Posts: 1484
Joined: Tue Oct 16, 2012 1:57 am
Location: Kitchener, Ontario, Canada
Contact:

Re: Jadgpanzer L70/V Build

Post by dgsselkirk »

Next some little detail parts like the mounts for the rear hull spaced armour, then started to work with the recoil. I decided I really wasn't interested in having elevation anyway so I simply made a barrel sleeve out of brass tubing and put it in the mantle. I used the asiatam one from the Mk. IV but just sort of the tray and attached a servo. What I have is a REALLY smooth recoil now! I will figure out how to post a video sometime. I did not use the barrel from the Panzerparts kit. It was too short and I don't think it was large enough caliber either. More like a 50 mm. Besides I have the BB Panthers so since this is to be the same gun I cut off the muzzle brake on an extra barrel I had, measured the length it should be to scale off my scale drawings and volia! Nice big long barrel! :D
Attachments
L70 build 19.jpg
L70 build 19.jpg (45.47 KiB) Viewed 5564 times
L70 build 18.jpg
L70 build 18.jpg (45.48 KiB) Viewed 5564 times
L70 build 17.jpg
L70 build 17.jpg (40.15 KiB) Viewed 5564 times
L70 build 16.jpg
L70 build 16.jpg (52.64 KiB) Viewed 5564 times
L70 build 15.jpg
L70 build 15.jpg (46.22 KiB) Viewed 5564 times
L70 build 14.jpg
L70 build 14.jpg (41.44 KiB) Viewed 5564 times
L70 build 12.jpg
L70 build 12.jpg (56.48 KiB) Viewed 5564 times
L70 build 11.jpg
L70 build 11.jpg (59.33 KiB) Viewed 5564 times
L70 build 10.jpg
L70 build 10.jpg (37.4 KiB) Viewed 5564 times
"There are things in Russia which are not as they seem..."
Georgy Konstantinovich Zhukov
User avatar
dgsselkirk
Warrant Officer 2nd Class
Posts: 1484
Joined: Tue Oct 16, 2012 1:57 am
Location: Kitchener, Ontario, Canada
Contact:

Re: Jadgpanzer L70/V Build

Post by dgsselkirk »

On the next set of pics we have the work on the zim. Again, I did splurge and bought the Atak sheets of zim and cut and fit. I decided to open up the machinegun cover and install a metal LED one I had. Also did the mount and wiring for the front light. As you can see or maybe not there are metal engine covers as well.
Attachments
L70 build 29.jpg
L70 build 29.jpg (59.08 KiB) Viewed 5563 times
L70 build 28.jpg
L70 build 28.jpg (59.88 KiB) Viewed 5563 times
L70 build 27.jpg
L70 build 27.jpg (50.62 KiB) Viewed 5563 times
L70 build 26.jpg
L70 build 26.jpg (54.42 KiB) Viewed 5563 times
L70 build 25.jpg
L70 build 25.jpg (51.88 KiB) Viewed 5563 times
L70 build 24.jpg
L70 build 24.jpg (54.97 KiB) Viewed 5563 times
L70 build 23.jpg
L70 build 23.jpg (59.55 KiB) Viewed 5563 times
L70 build 22.jpg
L70 build 22.jpg (57.18 KiB) Viewed 5563 times
L70 build 21.jpg
L70 build 21.jpg (61.17 KiB) Viewed 5563 times
"There are things in Russia which are not as they seem..."
Georgy Konstantinovich Zhukov
ALPHA
Major-General
Posts: 10963
Joined: Thu Oct 03, 2013 1:06 am

Re: Jadgpanzer L70/V Build

Post by ALPHA »

Hey dgsselkirk :wave: ....so this is the Jagd you spoke of ... very nice... :D couldn't find it on the link you left on my thread...
Nice board by the way :thumbup: you all have some really cool meets...those guys are hard core 8O

Thanks for posting the great picturesImage

Happy TankingImage

ALPHA
User avatar
dgsselkirk
Warrant Officer 2nd Class
Posts: 1484
Joined: Tue Oct 16, 2012 1:57 am
Location: Kitchener, Ontario, Canada
Contact:

Re: Jadgpanzer L70/V Build

Post by dgsselkirk »

Thanks Alpha, they are a pretty good bunch of guys. We don't go anal on the rules which makes it fun for everyone.

so here are some pics of the zim around the mantle. This was done by cutting small sections out of the sheet and spacing it around in a curve. Also mounted scratch built springs on the rear fender. I sliced off the bolts on the back plate of the upper hull and then put them back on after attaching the zim. The trick was once I had sliced them off I put some tracing paper over to mark where they went. Then put the zim on and laid the tracing paper on top and using a small drill (you could use a sharp pencil) marked where everything went and glued them back on. I think it worked quite well. Because they are sliced off they are a little thinner so that sitting on the zim they look about the right depth.
I am leaving the front fenders off so all I installed were some scratch built mounts. I added styrene bolts later.
Attachments
L70 build 39.jpg
L70 build 39.jpg (46.31 KiB) Viewed 5539 times
L70 build 38.jpg
L70 build 38.jpg (44.67 KiB) Viewed 5539 times
L70 build 37.jpg
L70 build 37.jpg (46.72 KiB) Viewed 5539 times
L70 build 36.jpg
L70 build 36.jpg (44.06 KiB) Viewed 5539 times
L70 build 35.jpg
L70 build 35.jpg (40.22 KiB) Viewed 5539 times
L70 build 34.jpg
L70 build 34.jpg (56.99 KiB) Viewed 5539 times
L70 build 33.jpg
L70 build 33.jpg (54.73 KiB) Viewed 5539 times
L70 build 32.jpg
L70 build 32.jpg (44.31 KiB) Viewed 5539 times
L70 build 31.jpg
L70 build 31.jpg (54.95 KiB) Viewed 5539 times
L70 build 30.jpg
L70 build 30.jpg (54.1 KiB) Viewed 5539 times
"There are things in Russia which are not as they seem..."
Georgy Konstantinovich Zhukov
User avatar
tomhugill
Captain
Posts: 4745
Joined: Thu Apr 15, 2010 11:21 am

Re: Jadgpanzer L70/V Build

Post by tomhugill »

Looks great! How did you find the fitting of the parts? I've been told the quality can be a bit questionable but I'd like another opinion before I go for one!
User avatar
Swamprat33
Lance Corporal
Posts: 241
Joined: Wed Aug 29, 2012 10:48 pm
Location: Milton Keynes Area

Re: Jadgpanzer L70/V Build

Post by Swamprat33 »

Hiya, I have not really started research for my L48 yet, but had always wondered what the conical things (mg covers) were.
I think I will open one up to house the IR for the battle system. The conical 'plug' can be removed and refitted when required.
I did a similar thing on my Panzer IV G. It does obviously limit the benefit of elevation, but I guess I can live with it.

Tim
1/6 Armortek Panther ausf.G
1/6 Armortek Panzer III ausf.J
1/6 Type 82 Funkwagen
1/6 Sdkfz 250/9
1/6 Sdkfz 2 Kettenkrad
User avatar
dgsselkirk
Warrant Officer 2nd Class
Posts: 1484
Joined: Tue Oct 16, 2012 1:57 am
Location: Kitchener, Ontario, Canada
Contact:

Re: Jadgpanzer L70/V Build

Post by dgsselkirk »

tomhugill wrote:Looks great! How did you find the fitting of the parts? I've been told the quality can be a bit questionable but I'd like another opinion before I go for one!
I was O.K. with it for the price Tom. I want this tank to battle so the construction is a little heavier and cruder for strength than if you were just building it for show. The hardest part was setting up the front lower hull nose properly. I am not exact but close enough for government work! :D
I am pretty happy with how it all went together but you do have to do some cutting and filing but I know your work. You will have no issues! :D

On another note, I can hardly wait to see the Panther "F" you are sending Michael! I really was after it for myself but I had/have 4 more projects lined up so I had to pass... :'( But Michael will let me play with it once in a while and I will have first dibs if he decides to sell it. :D
"There are things in Russia which are not as they seem..."
Georgy Konstantinovich Zhukov
User avatar
dgsselkirk
Warrant Officer 2nd Class
Posts: 1484
Joined: Tue Oct 16, 2012 1:57 am
Location: Kitchener, Ontario, Canada
Contact:

Re: Jadgpanzer L70/V Build

Post by dgsselkirk »

Swamprat33 wrote:Hiya, I have not really started research for my L48 yet, but had always wondered what the conical things (mg covers) were.
I think I will open one up to house the IR for the battle system. The conical 'plug' can be removed and refitted when required.
I did a similar thing on my Panzer IV G. It does obviously limit the benefit of elevation, but I guess I can live with it.

Tim
Mine was set up for a Hammerhead so I didn't have to worry about the emitter but if I build another one that is not a bad idea! What I would do is recess the emitter enough that you could actually put the cover on a swivel so that it functions like the real one. It would not be hard to do at all. Some models actually had one on each side so you could still do one MG and one as the emitter too.
"There are things in Russia which are not as they seem..."
Georgy Konstantinovich Zhukov
User avatar
PainlessWolf
Lieutenant-Colonel
Posts: 7399
Joined: Sun Feb 26, 2012 9:09 pm
Location: Southern Colorado Rocky Mountains

Re: Jadgpanzer L70/V Build

Post by PainlessWolf »

Good Morning,
Beautiful and involved work. For a battler, it certainly looks good enough to sit on anyone's shelf as well.
regards,
Painless
...Here for the Dawn...
Post Reply

Return to “Other Builds”