Hello
I have installed the El-mod Fusion pro board into my Tiger 1 and have it powered up and the blue light blinks, but I am having difficulty binding the FlySky FS-T6 transmitter to the El-mod Fusion Pro board. Has anybody got a step by step instuctions. I am unable to make sense of the supplied instructions. Many thanks.
Bind elmod fusion pro to flysky FS-T6 transmitter
- Rad_Schuhart
- Warrant Officer 1st Class
- Posts: 1979
- Joined: Tue Jan 19, 2016 9:22 am
- Location: Spanish living in Graz, Austria. Heart in UK.
- Contact:
Re: Bind elmod fusion pro to flysky FS-T6 transmitter
Just in case:
You know you have to bind the radio to the receiver and not to the Elmod board itself, right?
You know you have to bind the radio to the receiver and not to the Elmod board itself, right?
My RC tanks website, loads of free info for everybody:
https://radindustries.wordpress.com/
https://radindustries.wordpress.com/
Re: Bind elmod fusion pro to flysky FS-T6 transmitter
This seems to be a fair question. Hasn’t the person skipped on adding the receiver to the board.Rad_Schuhart wrote:Just in case:
You know you have to bind the radio to the receiver and not to the Elmod board itself, right?
Sent from my iPhone using Tapatalk
Started as a tank man.
2x early Tiger 1's made from parts of HL, Taigen, Mato and whatever I saw suitable.
Ural 4320 (~1/12)
WPL B36 Ural
2x early Tiger 1's made from parts of HL, Taigen, Mato and whatever I saw suitable.
Ural 4320 (~1/12)
WPL B36 Ural
Re: Bind elmod fusion pro to flysky FS-T6 transmitter
Good point! that is the problem, how to connect to the receiver? In the instructions I cant figure out how to do this.
I have a FS-R6B receiver with 6 channels, do the plugs go in with the wires on the outside edge or with the wire on the inside edge? This seems most important with the power lead is the black wire on the outside or inside edge?
I have a FS-R6B receiver with 6 channels, do the plugs go in with the wires on the outside edge or with the wire on the inside edge? This seems most important with the power lead is the black wire on the outside or inside edge?
Re: Bind elmod fusion pro to flysky FS-T6 transmitter
It’s on top of page 8 of the Eco/pro manual. The attached cable should be connected to the receiver based on cable colors. 5 slots occupied. The receiver is powered by the board through that connection.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Started as a tank man.
2x early Tiger 1's made from parts of HL, Taigen, Mato and whatever I saw suitable.
Ural 4320 (~1/12)
WPL B36 Ural
2x early Tiger 1's made from parts of HL, Taigen, Mato and whatever I saw suitable.
Ural 4320 (~1/12)
WPL B36 Ural
-
- Warrant Officer 1st Class
- Posts: 1663
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: Bind elmod fusion pro to flysky FS-T6 transmitter
Hello
As Rad asks? Have you linked the transmitter to the receiver? (Binder) see transmitter manual, then the wires go to the top of the RX and label side above, be careful the RX is powered by the plate (Bat.) Then just follow the instructions, and also determine how you want to use ( order) orders?
As Rad asks? Have you linked the transmitter to the receiver? (Binder) see transmitter manual, then the wires go to the top of the RX and label side above, be careful the RX is powered by the plate (Bat.) Then just follow the instructions, and also determine how you want to use ( order) orders?
-
- Warrant Officer 1st Class
- Posts: 1663
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: Bind elmod fusion pro to flysky FS-T6 transmitter
For information,
Ch.1 ..... Green wire turret rotation
Ch.2 ..... brown wire Gas (engines)
Ch.3 ..... yellow wire shooting and barrel elevation
Ch.4 ..... orange wire direction, right / left
Ch.5 ..... imperative blue thread
Ch.6 ..... purple / gray pilot options by switch (3 positions On: Off: On) or potentiometer,
for white, not used in the case of 6 channels, reserved for sound adjustment from the TX. Always according to the position of the desired controls on the TX, it is therefore necessary to mark the channels with the front servos.
Ch.1 ..... Green wire turret rotation
Ch.2 ..... brown wire Gas (engines)
Ch.3 ..... yellow wire shooting and barrel elevation
Ch.4 ..... orange wire direction, right / left
Ch.5 ..... imperative blue thread
Ch.6 ..... purple / gray pilot options by switch (3 positions On: Off: On) or potentiometer,
for white, not used in the case of 6 channels, reserved for sound adjustment from the TX. Always according to the position of the desired controls on the TX, it is therefore necessary to mark the channels with the front servos.
Re: Bind elmod fusion pro to flysky FS-T6 transmitter
Binding completed. Many thanks for your help.
Re: Bind elmod fusion pro to flysky FS-T6 transmitter
Now the fun begins