Panzer 4 Shurzen.
- jarndice
- Colonel
- Posts: 8003
- Joined: Mon Sep 03, 2012 11:27 am
- Location: the mountains of hertfordshire
Panzer 4 Shurzen.
I have downloaded the file on the PZ4 Shurzen and it appears to have all the information I need EXCEPT the thickness of the Brass sheet and the width of the Brackets
I figure either 2mm or 3mm for the sheet but I have no idea about the brackets, can anyone give me the actual widths ?
I figure either 2mm or 3mm for the sheet but I have no idea about the brackets, can anyone give me the actual widths ?
I think I am about to upset someone
- Raminator
- Warrant Officer 2nd Class
- Posts: 1266
- Joined: Tue Aug 11, 2015 9:57 am
- Location: Newcastle, Australia
Re: Panzer 4 Shurzen.
If I recall correctly schürzen were 5 mm on the hull and 8 mm on the turret, so 0.5 mm brass sheet would give you scale thickness.
- HERMAN BIX
- Brigadier
- Posts: 10235
- Joined: Sun Jan 12, 2014 12:15 am
- Location: Gold Coast,Australia
Re: Panzer 4 Shurzen.
Best advice from me is use material you can cut with a good pair of industrial scissors.
Unless you have a guillotine of course.
0.3mm or 0.4mm if you can get it.
I used 0.5mm but it was too thick for scissors and I had to use snips.
Then spent ages dressing the cut edges.
Unless you have a guillotine of course.
0.3mm or 0.4mm if you can get it.
I used 0.5mm but it was too thick for scissors and I had to use snips.
Then spent ages dressing the cut edges.
HL JAGDPANTHER,HL TIGER 1,HL PzIII MUNITIONSCHLEPPER, HL KT OCTOPUS,HL PANTHER ZU-FUSS,HL STuG III,HL T34/85 BEDSPRING,
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
- jarndice
- Colonel
- Posts: 8003
- Joined: Mon Sep 03, 2012 11:27 am
- Location: the mountains of hertfordshire
Re: Panzer 4 Shurzen.
Thank you Gentlemen, Most helpful,
I was about to start looking for a supplier of CHEEP Brass sheet but in the fine tradition of modellers worldwide I searched around the house first,
Did you know that a Heinz Chicken and Mushroom steel soup tin is 0.26mm thick,10.5cms wide and 22cms long ? Being steel it is of course magnetic which is handy if you are looking for an alternative way of keeping body and hull together when combined with a couple of countersunk magnets.
And the soup was delicious
As to softening the edges I usually clamp a file in the vice and using a pair of industrial gloves run sharp or burred edges along the file and that's another job done.
For a soft finish I run the edge along an oil stone,
I was about to start looking for a supplier of CHEEP Brass sheet but in the fine tradition of modellers worldwide I searched around the house first,
Did you know that a Heinz Chicken and Mushroom steel soup tin is 0.26mm thick,10.5cms wide and 22cms long ? Being steel it is of course magnetic which is handy if you are looking for an alternative way of keeping body and hull together when combined with a couple of countersunk magnets.
And the soup was delicious
As to softening the edges I usually clamp a file in the vice and using a pair of industrial gloves run sharp or burred edges along the file and that's another job done.
For a soft finish I run the edge along an oil stone,
I think I am about to upset someone
- jarndice
- Colonel
- Posts: 8003
- Joined: Mon Sep 03, 2012 11:27 am
- Location: the mountains of hertfordshire
Re: Panzer 4 Shurzen.
Not Under my HAMMER they dontSon of a gun-ner wrote:But what about the corrugated strengthening those tins have?
I think I am about to upset someone
- jarndice
- Colonel
- Posts: 8003
- Joined: Mon Sep 03, 2012 11:27 am
- Location: the mountains of hertfordshire
Re: Panzer 4 Shurzen.
After 45 years we seem to be getting the hang of each other
As to the neighbours, we have woods to the back and one side and a farm on the other and a lane to the front.
As to the neighbours, we have woods to the back and one side and a farm on the other and a lane to the front.
I think I am about to upset someone
- PainlessWolf
- Lieutenant-Colonel
- Posts: 7399
- Joined: Sun Feb 26, 2012 9:09 pm
- Location: Southern Colorado Rocky Mountains
Re: Panzer 4 Shurzen.
Good morning,
It works well! The unsuspecting "populace" around here is usually down at one of the two saloons that this town sports or out herding cattle. I'm usually out back 'filing and cussing' or 'banging on things with a brass hammer and cussing'. Take your pick! Jarndice understands.
regards,
Painless
( Thanks for letting me add my two cents about living out in the 'Blue' )
It works well! The unsuspecting "populace" around here is usually down at one of the two saloons that this town sports or out herding cattle. I'm usually out back 'filing and cussing' or 'banging on things with a brass hammer and cussing'. Take your pick! Jarndice understands.
regards,
Painless
( Thanks for letting me add my two cents about living out in the 'Blue' )
...Here for the Dawn...
- Raminator
- Warrant Officer 2nd Class
- Posts: 1266
- Joined: Tue Aug 11, 2015 9:57 am
- Location: Newcastle, Australia
Re: Panzer 4 Shurzen.
Painless, you are a man after my own heart. I can't get anything done without a helpful dose of colourful language.
- Raminator
- Warrant Officer 2nd Class
- Posts: 1266
- Joined: Tue Aug 11, 2015 9:57 am
- Location: Newcastle, Australia
Re: Panzer 4 Shurzen.
For XF-49's sake Mick, don't be so X-28 obtuse.
- Will01Capri
- 2nd Lieutenant
- Posts: 2704
- Joined: Tue Jul 18, 2017 5:34 pm
- Location: South Scotland
Re: Panzer 4 Shurzen.
Does anyone have any blueprints and detailed pictures of Side Shurzen for a Panzer IV?
I need to look at adding to my H Panzer IV. Although i think i will probably take the plasticasrd route and 3d print small details and attachments for it
I need to look at adding to my H Panzer IV. Although i think i will probably take the plasticasrd route and 3d print small details and attachments for it
HL camo E' Tiger
HL L' Tiger
M26 Pershing WW2 project
Tam K'Tiger project
HL Walker Bulldog project?
HL Panzer IV Munitionsschlepper für Karl-Gerät
HL Sherman project?
1/24 Leopard 2 Custom mod
2 many trucks to list!
HL L' Tiger
M26 Pershing WW2 project
Tam K'Tiger project
HL Walker Bulldog project?
HL Panzer IV Munitionsschlepper für Karl-Gerät
HL Sherman project?
1/24 Leopard 2 Custom mod
2 many trucks to list!