PzKpfw II L35rctank conversion construction
PzKpfw II L35rctank conversion construction
( I moved this post from another thread.) I recently gathered the Classy Hobby PzKpfw II L luchs plastic kit and the 35rctanks rc conversion kit. I'm going to start posting occasionally about this project. let me know if it's of interest!
First off, here's what you get in the conversion kit, from top left across:
> turret assembly with rotation motor, elevation servo, and a control board.
> humungous speaker!
> turret ring, torsion bars, assorted small parts.
> solenoid operated recoil main auto-cannon.
> main control board.
> motors and gearboxes.
First off, here's what you get in the conversion kit, from top left across:
> turret assembly with rotation motor, elevation servo, and a control board.
> humungous speaker!
> turret ring, torsion bars, assorted small parts.
> solenoid operated recoil main auto-cannon.
> main control board.
> motors and gearboxes.
Last edited by SoCalBobS on Thu Sep 23, 2021 5:58 pm, edited 1 time in total.
Renault FT, British WW1 Mk. 4), Pz 1A DAK, 1B, II L, III, StuG III, PzKpfw IV, StuG IV, King Tiger, T-34/76, KV-1E, T-35A 3DP, Zik-2, T-90, M3 Lee, M4 Sherman, M26 Pershing, M41 Bulldog, M1 Abrams. In the works: Ram II, Pz 1 Breda.
Re: PzKpfw II L35rctank conversion construction
The most critical step is the installation of the drive gear, which requires some surgery. It's gotta be aligned correctly.
A hole must be ground out on the hull side for the gearbox assembly to fit through. The hole in the transmission cover has to be enlarged. There is an adapter cylinder that fits on the gearbox axle and is glued onto the sprocket wheel.
The gearboxes have a plastic part that is to be glued onto the hull side to position and secure the gearbox. The plastic part is bolted onto the gearbox frame so so it can be removed if necessary.
A hole must be ground out on the hull side for the gearbox assembly to fit through. The hole in the transmission cover has to be enlarged. There is an adapter cylinder that fits on the gearbox axle and is glued onto the sprocket wheel.
The gearboxes have a plastic part that is to be glued onto the hull side to position and secure the gearbox. The plastic part is bolted onto the gearbox frame so so it can be removed if necessary.
Renault FT, British WW1 Mk. 4), Pz 1A DAK, 1B, II L, III, StuG III, PzKpfw IV, StuG IV, King Tiger, T-34/76, KV-1E, T-35A 3DP, Zik-2, T-90, M3 Lee, M4 Sherman, M26 Pershing, M41 Bulldog, M1 Abrams. In the works: Ram II, Pz 1 Breda.
- midlife306
- Warrant Officer 1st Class
- Posts: 2238
- Joined: Sun Aug 27, 2017 10:34 am
Re: PzKpfw II L35rctank conversion construction
I’ll grab a large bag of popcorn
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
- 43rdRecceReg
- Major
- Posts: 6294
- Joined: Fri Jul 31, 2015 11:38 am
- Location: North West Highlands, Scotland
Re: PzKpfw II L35rctank conversion construction
Do continue It's an original project, and certainly a welcome foray into non-mainstream builds
"Get your facts first, and then you can distort them as much as you please"- Mark Twain.
Re: PzKpfw II L35rctank conversion construction
The electronics:
MTC; Main Tank Controller (their terms). Five wires plug into Receiver.
Receiver; 4+ channel. Fifth channel used for GSU; Gyroscopic Stabilizer Unit, not on this tank.
Battery. 2S lipo. MTC cuts off power at 6V, saving the battery.
Motors/Gears. Plug into sockets on MTC.
ACU; Auxiliary Control Unit. Four wire connector plugs into MTC. ACU runs guns and turret.
MTC; Main Tank Controller (their terms). Five wires plug into Receiver.
Receiver; 4+ channel. Fifth channel used for GSU; Gyroscopic Stabilizer Unit, not on this tank.
Battery. 2S lipo. MTC cuts off power at 6V, saving the battery.
Motors/Gears. Plug into sockets on MTC.
ACU; Auxiliary Control Unit. Four wire connector plugs into MTC. ACU runs guns and turret.
Renault FT, British WW1 Mk. 4), Pz 1A DAK, 1B, II L, III, StuG III, PzKpfw IV, StuG IV, King Tiger, T-34/76, KV-1E, T-35A 3DP, Zik-2, T-90, M3 Lee, M4 Sherman, M26 Pershing, M41 Bulldog, M1 Abrams. In the works: Ram II, Pz 1 Breda.
- Herr Dr. Professor
- Lieutenant
- Posts: 3616
- Joined: Mon Apr 22, 2019 10:48 pm
- Location: Southern Wisconsin USA
Re: PzKpfw II L35rctank conversion construction
I have a Luchs as well as some other small 1/16 static tank kits. Who knows, maybe someday.... So I am watching, too.
Re: PzKpfw II L35rctank conversion construction
Coordinating the construction requirements between the model and the conversion takes some thought! Here is some important info about the running mechanisms:
Earlier I showed how the gearboxes fit into the hull. Eventually they will be glued onto the hull sides, but not yet! Right now I'm doing a lot of valuable dry fitting. The conversion has a functional torsion bar suspension, and the many components have to be lined up precisely. The "bars" themselves, actually spring steel strips, have to be threaded through many holes, and of course have to be aligned correctly.
The bars go through the side wall, through a conversion kit black strip, through the model kit gray strip, across to the second gray strip and finally to a slot in the second black strip, where it is glued. the strips are not symmetrical, either in shape or placement. There is a left and a right. All need to be lined up correctly before being glued so that the bars are free to twist. The bars should not be glued yet, because the swing arms that go on the outside ends need to be attached and the wheels need to be lined up to align with the tracks. You can see that if the motor had been glued, it would have been very difficult to assemble the suspension. One diagram in the conversion manual shows the plastic section of the gearbox glued onto the sidewall, but the gearbox removed. This can be done because the box is bolted into the plastic part, but it's better to just wait until the suspension is placed and glued. Just another view. This thread is not meant to be a complete "how to", but simply spots where I think additional explanation is needed.
Earlier I showed how the gearboxes fit into the hull. Eventually they will be glued onto the hull sides, but not yet! Right now I'm doing a lot of valuable dry fitting. The conversion has a functional torsion bar suspension, and the many components have to be lined up precisely. The "bars" themselves, actually spring steel strips, have to be threaded through many holes, and of course have to be aligned correctly.
The bars go through the side wall, through a conversion kit black strip, through the model kit gray strip, across to the second gray strip and finally to a slot in the second black strip, where it is glued. the strips are not symmetrical, either in shape or placement. There is a left and a right. All need to be lined up correctly before being glued so that the bars are free to twist. The bars should not be glued yet, because the swing arms that go on the outside ends need to be attached and the wheels need to be lined up to align with the tracks. You can see that if the motor had been glued, it would have been very difficult to assemble the suspension. One diagram in the conversion manual shows the plastic section of the gearbox glued onto the sidewall, but the gearbox removed. This can be done because the box is bolted into the plastic part, but it's better to just wait until the suspension is placed and glued. Just another view. This thread is not meant to be a complete "how to", but simply spots where I think additional explanation is needed.
Renault FT, British WW1 Mk. 4), Pz 1A DAK, 1B, II L, III, StuG III, PzKpfw IV, StuG IV, King Tiger, T-34/76, KV-1E, T-35A 3DP, Zik-2, T-90, M3 Lee, M4 Sherman, M26 Pershing, M41 Bulldog, M1 Abrams. In the works: Ram II, Pz 1 Breda.
- HERMAN BIX
- Brigadier
- Posts: 10311
- Joined: Sun Jan 12, 2014 12:15 am
- Location: Gold Coast,Australia
Re: PzKpfw II L35rctank conversion construction
And we all appreciate your doing it I’m sure !
These kits have been around a while and now are starting to become hard. To get, the conversion kits might make that availability worse
These kits have been around a while and now are starting to become hard. To get, the conversion kits might make that availability worse
HL JAGDPANTHER,HL TIGER 1,HL PzIII MUNITIONSCHLEPPER, HL KT OCTOPUS,HL PANTHER ZU-FUSS,HL STuG III,HL T34/85 BEDSPRING,
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
Re: PzKpfw II L35rctank conversion construction
Yeah, it's an older production run, but some folks still have them. I did buy mine just a month ago, online. I do have an online buddy following my steps for his build.
Next step, actually continuing the torsion bar assembly: the conversion manual is sparse, so I took a couple photos to flesh it out.
The original torsion bar and swing arm is one piece. Conversion requires cutting off the rod part and making a hole and slot for the steel strip.
Original rod on left, cut off swing arm with hole and slot, and the strip inserted in the swing arm. Drilling and cutting has to be done carefully, I used a small drill press and a dremel. Notice I numbered the swing arms. They're not all the same, and not readlily so apparent. It'll get wiped and painted over later.
Next step, actually continuing the torsion bar assembly: the conversion manual is sparse, so I took a couple photos to flesh it out.
The original torsion bar and swing arm is one piece. Conversion requires cutting off the rod part and making a hole and slot for the steel strip.
Original rod on left, cut off swing arm with hole and slot, and the strip inserted in the swing arm. Drilling and cutting has to be done carefully, I used a small drill press and a dremel. Notice I numbered the swing arms. They're not all the same, and not readlily so apparent. It'll get wiped and painted over later.
Renault FT, British WW1 Mk. 4), Pz 1A DAK, 1B, II L, III, StuG III, PzKpfw IV, StuG IV, King Tiger, T-34/76, KV-1E, T-35A 3DP, Zik-2, T-90, M3 Lee, M4 Sherman, M26 Pershing, M41 Bulldog, M1 Abrams. In the works: Ram II, Pz 1 Breda.
Re: PzKpfw II L35rctank conversion construction
Time for a break! Torsion rod/swing arms completed, next up would be to attach wheels. But they have to be painted first, as well as the lower hull, which means detail pieces have to be attached. I'll return when that is done.
Renault FT, British WW1 Mk. 4), Pz 1A DAK, 1B, II L, III, StuG III, PzKpfw IV, StuG IV, King Tiger, T-34/76, KV-1E, T-35A 3DP, Zik-2, T-90, M3 Lee, M4 Sherman, M26 Pershing, M41 Bulldog, M1 Abrams. In the works: Ram II, Pz 1 Breda.