BMP-1 IFV - Soviet army, Afghanistan 1980s - Build
Re: BMP-1 IFV - Soviet army, Afghanistan 1980s - Build
Hi, well thank you very much.
I know most guys like to neatly spread out their complex electronics over the whole length of the interior, sometimes with many speakers and exotic control cards. Although the model is rich in RC features, the focus of this build is different. As an APC with large doors, it was screaming at me for interior details, rotating turret basket and infantry to really come alive. BMPs are rare. I saw a few Russian BMPs on YouTube. They really like to make them amphibious and throw them in a lake to swim around. I prefer dry land and to also keep the finish dry on my models. I know how much damage water can do to a paint job. I hope the Russians will like it.
Here presenting the finished turret exterior.
The Ludwigs kit only provides a skeleton turret shape and a couple of plasticard plates so everything else needs to be studied and scratch built. The Topshots book on the BMP1 is therefore essential with close ups of most components to fill the gaps.
The completed turret. It is small but I equipped it well. I was previously able to give it a turret basket interior, turret rotation, gun elevation, gun recoil, gun flash, coax MG flash. Now it also has a working spotlight and a manually opening gunner's hatch. There is a large number of electrical cables coming out of the bottom.
I had to study all references to recreate the exterior. The spotlight is an T55 item from AFV_Model, the rest is scratch built the best I could with what I had in material, with the couple of days I wanted to spend on it. The optical device was fun to build in brass.
I decided to create the Sagger missile launcher ramp on top of the gun barrel although I did see that it was sometimes removed completely. No short cut...
The long trap door behind the Sagger missile ramp is for the gunner who opens it in order to manually slide a new missile on the launching ramp without being too exposed.
The 1/16 Maim 3D printed Russian gunner figure shows how small the BMP one man turret really is.
The inside of the gunner's hatch was given details because it will remain opened.
A 5mm LED was inserted into the AFF-Model spotlight. I saw some BMPs with a infra red lights instead of the provided white spotlight so it is an alternative. The clear lens will be installed only after painting.
Close up of the Sagger missile ramp. I kept the detailing to a medium level.
Next step focus will be on the exterior rear of the vehicle. Installing those rear doors in a way that they can be manually opened and closed will be something.
Regards, Louis
I know most guys like to neatly spread out their complex electronics over the whole length of the interior, sometimes with many speakers and exotic control cards. Although the model is rich in RC features, the focus of this build is different. As an APC with large doors, it was screaming at me for interior details, rotating turret basket and infantry to really come alive. BMPs are rare. I saw a few Russian BMPs on YouTube. They really like to make them amphibious and throw them in a lake to swim around. I prefer dry land and to also keep the finish dry on my models. I know how much damage water can do to a paint job. I hope the Russians will like it.
Here presenting the finished turret exterior.
The Ludwigs kit only provides a skeleton turret shape and a couple of plasticard plates so everything else needs to be studied and scratch built. The Topshots book on the BMP1 is therefore essential with close ups of most components to fill the gaps.
The completed turret. It is small but I equipped it well. I was previously able to give it a turret basket interior, turret rotation, gun elevation, gun recoil, gun flash, coax MG flash. Now it also has a working spotlight and a manually opening gunner's hatch. There is a large number of electrical cables coming out of the bottom.
I had to study all references to recreate the exterior. The spotlight is an T55 item from AFV_Model, the rest is scratch built the best I could with what I had in material, with the couple of days I wanted to spend on it. The optical device was fun to build in brass.
I decided to create the Sagger missile launcher ramp on top of the gun barrel although I did see that it was sometimes removed completely. No short cut...
The long trap door behind the Sagger missile ramp is for the gunner who opens it in order to manually slide a new missile on the launching ramp without being too exposed.
The 1/16 Maim 3D printed Russian gunner figure shows how small the BMP one man turret really is.
The inside of the gunner's hatch was given details because it will remain opened.
A 5mm LED was inserted into the AFF-Model spotlight. I saw some BMPs with a infra red lights instead of the provided white spotlight so it is an alternative. The clear lens will be installed only after painting.
Close up of the Sagger missile ramp. I kept the detailing to a medium level.
Next step focus will be on the exterior rear of the vehicle. Installing those rear doors in a way that they can be manually opened and closed will be something.
Regards, Louis
- c.rainford73
- Major
- Posts: 6104
- Joined: Thu Aug 25, 2016 7:34 pm
- Location: Connecticut USA
Re: BMP-1 IFV - Soviet army, Afghanistan 1980s - Build
Outstanding work Louis. The bits you cobbled together in a "few days" look just fantastic, and would take the rest of us a few weeks to attempt to replicate if we could.
Tanks alot....
Re: BMP-1 IFV - Soviet army, Afghanistan 1980s - Build
Hi there is a company called attracks, I've seen them of Facebook and met him at the Telford model show, he was showing off some 1/16 bmp tracks and sprockets that he had designed and cast hope this helps.
- HERMAN BIX
- Brigadier
- Posts: 10321
- Joined: Sun Jan 12, 2014 12:15 am
- Location: Gold Coast,Australia
Re: BMP-1 IFV - Soviet army, Afghanistan 1980s - Build
Not got much to say
Following on in humble amazement
Following on in humble amazement
HL JAGDPANTHER,HL TIGER 1,HL PzIII MUNITIONSCHLEPPER, HL KT OCTOPUS,HL PANTHER ZU-FUSS,HL STuG III,HL T34/85 BEDSPRING,
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
Re: BMP-1 IFV - Soviet army, Afghanistan 1980s - Build
Herman, when I read that the first thing that came to mind is that old song ... Lying in a Den in Bombay, with a slack jaw, and not much to say ...
But you're not the only one that's amazed. This Louis cat really boggles my mind with his talent. I only hope I'm half that good when I grow up.
But you're not the only one that's amazed. This Louis cat really boggles my mind with his talent. I only hope I'm half that good when I grow up.
When FDR coined the phrase "The Arsenal of Democracy", he was talking about Detroit. Proud to live in the 2nd most violent city in America!!
Re: BMP-1 IFV - Soviet army, Afghanistan 1980s - Build
Hi, thank you. Although his facebook page does not mention BMP tracks, there seems to be something very close to it on the picture of the display table. I will send an inquiry.stug 85 wrote:Hi there is a company called attracks, I've seen them of Facebook and met him at the Telford model show, he was showing off some 1/16 bmp tracks and sprockets that he had designed and cast hope this helps.
Me neither... I must tell you, a BMP build is not for everyone. There is not a single item on this build that is not a struggle to figure out, build, and integrate with the rest. And I mean everything. Its mainly a trial, error and learning experience. Many items had to be redone or repositioned twice. I also had some bad luck. The T34 TK-22 that I ordered is non functional and need to be replaced. I think the Sherman TK-22 I had been using as an interim for testing had an electrical short and is no longer responsive... I think its time for my vacation break. But so far, I have avoided critical mistakes and it should be a good looking BMP when its completed.HERMAN BIX wrote:Not got much to say
Regards, Louis
Re: BMP-1 IFV - Soviet army, Afghanistan 1980s - Build
Hi,
Presenting the BMP powertrain.
The nature of scratch building on a non commercial RC chassis is that the drive train elements are usually non existant and have to be figured out. I am not yet into 3D printing so there are limitationss. Below is what I put together, awaiting one day something better to put on the BMP.
This is the sprocket I had to get as close to as possible.
I previously tested a modified (highly reduced) HL Sherman sprocket to fit the 1/24 tracks but it ended up being too small and it did not look good. While going through the bone yard, I picked up old Tamiya 1/25 Centurion sprockets with teeth that seem to fit the Sherman 1/24 tracks quite well.
Here, the Centurion teeth wheels have been separated and tested on the tracks. Perfect fit.
Here are the components of the new BMP sprocket before assembly. A Heng Long Sherman sprocket has been cleaned up of all features and cut in half to become the core that will connect to the gearbox.
The assembled BMP sprocket. It looks a bit weird like this but it has some basic features of the real one and it runs well in testing. The 1/24 plastic tracks are very light so the plastic sprocket should not have problems running the BMP inside the house at least. Once provided with a hub cap, it should look better. It will have to do until something better becomes available on the market.
This is the BMP idler with 5 spokes
It was previously done using half of a T-90 sprocket and ball bearing inside. It looks ok and works well.
This is the real BMP return roller.
Scavenging the spare parts reserve, I ended up selecting Tamiya PZ-IV return rollers that I did not use on a previous project. Although the real roller is a drum type, the basic components were there to recreate something close enough, most of it will be hidden behind the side skirts. The hub cap is from the PZ-IV road wheels.
Once trimmed and reshaped, this is what it gives.
Comtinuing on following post
Presenting the BMP powertrain.
The nature of scratch building on a non commercial RC chassis is that the drive train elements are usually non existant and have to be figured out. I am not yet into 3D printing so there are limitationss. Below is what I put together, awaiting one day something better to put on the BMP.
This is the sprocket I had to get as close to as possible.
I previously tested a modified (highly reduced) HL Sherman sprocket to fit the 1/24 tracks but it ended up being too small and it did not look good. While going through the bone yard, I picked up old Tamiya 1/25 Centurion sprockets with teeth that seem to fit the Sherman 1/24 tracks quite well.
Here, the Centurion teeth wheels have been separated and tested on the tracks. Perfect fit.
Here are the components of the new BMP sprocket before assembly. A Heng Long Sherman sprocket has been cleaned up of all features and cut in half to become the core that will connect to the gearbox.
The assembled BMP sprocket. It looks a bit weird like this but it has some basic features of the real one and it runs well in testing. The 1/24 plastic tracks are very light so the plastic sprocket should not have problems running the BMP inside the house at least. Once provided with a hub cap, it should look better. It will have to do until something better becomes available on the market.
This is the BMP idler with 5 spokes
It was previously done using half of a T-90 sprocket and ball bearing inside. It looks ok and works well.
This is the real BMP return roller.
Scavenging the spare parts reserve, I ended up selecting Tamiya PZ-IV return rollers that I did not use on a previous project. Although the real roller is a drum type, the basic components were there to recreate something close enough, most of it will be hidden behind the side skirts. The hub cap is from the PZ-IV road wheels.
Once trimmed and reshaped, this is what it gives.
Comtinuing on following post
Re: BMP-1 IFV - Soviet army, Afghanistan 1980s - Build
Continuing with the power train
Return rollers installed
Side skirts needed to be temporarily put in place to determine if everything looked right.
Although these 1/24 VS Sherman chevrons are not accurate for the BMP, the width and shape of the tracks are pretty good. No need to adjust anything between the hull and side skirts to make then fit.
Looks good
Tested one of the road wheel hub cap. Looks good.
Overview of the model with one side of the tracks installed.
Man, it is looking like a BMP.
Next step is the the back of the vehicle. Here is a view of the real vehicle. I also need to order micro hinges for the side skirts.
No parts are provided for the rear of the sponsors attaching to the side skirt so this will be scratched built. You can also see that the hinges for the rear door will be a struggle to figure out. But that will be a story that will continue after my 2 weeks winter vacation.
Happy new year everyone, see you in 2 weeks.
Louis
Return rollers installed
Side skirts needed to be temporarily put in place to determine if everything looked right.
Although these 1/24 VS Sherman chevrons are not accurate for the BMP, the width and shape of the tracks are pretty good. No need to adjust anything between the hull and side skirts to make then fit.
Looks good
Tested one of the road wheel hub cap. Looks good.
Overview of the model with one side of the tracks installed.
Man, it is looking like a BMP.
Next step is the the back of the vehicle. Here is a view of the real vehicle. I also need to order micro hinges for the side skirts.
No parts are provided for the rear of the sponsors attaching to the side skirt so this will be scratched built. You can also see that the hinges for the rear door will be a struggle to figure out. But that will be a story that will continue after my 2 weeks winter vacation.
Happy new year everyone, see you in 2 weeks.
Louis
- rmichalbarna
- Private
- Posts: 93
- Joined: Tue Jan 01, 2019 11:55 am
- Location: Most Czech republik
Re: BMP-1 IFV - Soviet army, Afghanistan 1980s - Build
I love Bmp! Very good!
Re: BMP-1 IFV - Soviet army, Afghanistan 1980s - Build
i'm crazy when i see your job
if you re interested i'm draw a lot of parts in 3d
for your sprocket i'm do mine with shapeways for my leclerc tank
https://www.shapeways.com/product/S8UQF ... -inventory
with professional plastic it's top to our models
if you re interested i'm draw a lot of parts in 3d
for your sprocket i'm do mine with shapeways for my leclerc tank
https://www.shapeways.com/product/S8UQF ... -inventory
with professional plastic it's top to our models