Leopard 1A4

Post Reply
User avatar
sparks
Warrant Officer 2nd Class
Posts: 1152
Joined: Thu Sep 23, 2010 10:57 pm

Leopard 1A4

Post by sparks »

Well, finally made a start .
Step 1. Take one perfectly good rear bulkhead......then cut and grind the living cr*p out of it to remove all the detail.
Image

Step 2 . Replace all the detail with metal upgrade parts :/
Image

I am using this (and other) photos for refference.
Image

I have had to re-locate the spare track holders a bit, as I want to hang spare track links on the back as in photo above.But the tracks that I have just built(see "For all you Leopard 1 fans") seem to be a bit wider scalewise than the real thing.
I have finished the painting of convoy marker as this AFV one is fixed on by a small strip of foam rubber that allows it to hinge like the original and it would be hard to hold it still to paint the cross,so it is temporarily in place and can be removed when I spray the rest of the bulkhead.The toolbox too is temporary as I have some PE parts on order, mainly for the tool holders, but the sheet also includes the tool boxes.
Image
BTW the electronics conversion kit is on its way (posted from HK today) :D
BFN sparks
sparks
Hey man....I just ride 'em, I dunno what makes 'em work.
Woof woof woof !
User avatar
Andy in Cheltenham
Corporal
Posts: 427
Joined: Mon Sep 21, 2009 12:54 pm
Location: Tewkesbury

Re: Leopard 1A4

Post by Andy in Cheltenham »

Ok......you've got me hooked....... :thumbup:
User avatar
sparks
Warrant Officer 2nd Class
Posts: 1152
Joined: Thu Sep 23, 2010 10:57 pm

Re: Leopard 1A4

Post by sparks »

Still fiddling with the rear bulkhead, apart from playing about with the convoy light ,
Image
Image
I've added some chain to the tow hook.
Image
Image
I won't even try to explain how hard that was for my 60 year old eyes :haha:
The PE parts have arrived so I will have a go at the rear tool box, as thats quite large :D , but it is a working box and those hinges and clasps look awfully small :/
Hey man....I just ride 'em, I dunno what makes 'em work.
Woof woof woof !
User avatar
sparks
Warrant Officer 2nd Class
Posts: 1152
Joined: Thu Sep 23, 2010 10:57 pm

Re: Leopard 1A4

Post by sparks »

Made a start on the PE rear tool box, another learning curve :/
Image
They recommend soldering the joints if using on RC model, so thats what I've done, tried to keep the exterior looking tidy.
Image
Image
Image
0.6mm rivets :wtf:
Image
I don't supose anyones come across a miniature riveting gun so I'll solder them inside the box.
Image

Hats off to the guys that do this in 1/35 scale :haha:
Hey man....I just ride 'em, I dunno what makes 'em work.
Woof woof woof !
User avatar
Andy in Cheltenham
Corporal
Posts: 427
Joined: Mon Sep 21, 2009 12:54 pm
Location: Tewkesbury

Re: Leopard 1A4

Post by Andy in Cheltenham »

Splendid bit of work mate.
User avatar
sparks
Warrant Officer 2nd Class
Posts: 1152
Joined: Thu Sep 23, 2010 10:57 pm

Re: Leopard 1A4

Post by sparks »

More work on the rear tool box.
Image
Image
Image
Image

Are these the NUTS (and bolts) or what
:D
Image
I can barely see them, let alone thread them together :D
These things laugh in the face of the carpet monster, they can be devoured by the.......................................

Laminate Flooring Monster :crazy:
Image
Image
Leaving the pins long because I want to remove the box for painting.
Image
Image
Just the closing rods to make now, that requires fitting some minute tee pieces into 1mm OD brass tubing :wtf:
Hey man....I just ride 'em, I dunno what makes 'em work.
Woof woof woof !
User avatar
sparks
Warrant Officer 2nd Class
Posts: 1152
Joined: Thu Sep 23, 2010 10:57 pm

Re: Leopard 1A4

Post by sparks »

Havn't been up to much lately, still waiting for some 1mm OD brass tubing.
In line with the instructions with the K11 electronics kit, I have removed the pivot slots from the lower turret part C9.
Image
I have also had to remove the locating pins on the inside of the barrel halfs, remove a mid and end section, and increase the inside diametre of the rear section to allow the recoil to operate.
Image
Hey man....I just ride 'em, I dunno what makes 'em work.
Woof woof woof !
User avatar
sparks
Warrant Officer 2nd Class
Posts: 1152
Joined: Thu Sep 23, 2010 10:57 pm

Re: Leopard 1A4

Post by sparks »

Sorry for lack of activity here, I finally got the 1mm OD tubing and soldered the 'T' pieces in to make the locking bars for the rear box.
Image
Then I had to form the hook part that bolts to the rear bulkhead for the locking bars to hook into.
Thats when the problems started :-<
I just couldn't bend them enough to work properly, it just seemed there wasn't enough length to work with, of course, after bending several times, they snapped. Only one pair is needed, but there are two pairs supplied,
(perhaps that says something), anyway, still managed to snap all of them.
By this time I was very frustrated and disillusioned, so I had to walk away from it for a while, then been busy with work and family stuff.
Anyway, started again last night with a positive attitude and scratch built my own hooks.
Image
Image
A tad larger than the photo etch ones but at least they work :thumbup:
Image
Image

A little finishing touch :/
Image
Hey man....I just ride 'em, I dunno what makes 'em work.
Woof woof woof !
magmer
Lance Corporal
Posts: 246
Joined: Tue Sep 29, 2009 10:03 am
Location: Southport. NW UK

Re: Leopard 1A4

Post by magmer »

That is looking fantastic, a briliant piece of detail work :clap:
User avatar
sparks
Warrant Officer 2nd Class
Posts: 1152
Joined: Thu Sep 23, 2010 10:57 pm

Re: Leopard 1A4

Post by sparks »

magmer wrote:That is looking fantastic, a briliant piece of detail work :clap:
Thanks magmer
Hey man....I just ride 'em, I dunno what makes 'em work.
Woof woof woof !
Post Reply

Return to “Modern Builds”