Hi, me again I'm afraid.
I have now got my IBU2U Full loosely fitted into my Torro / Taigen KT and pretty much all wired up.
A couple of / few things are puzzling me. Does the Taigen / Torro IR work with an IBU2U Full? If so, I can't get mine to work. If not, what do I need please?
Another puzzlement is that I've assigned the 10 channels on my FlySky 10 channel receiver correctly, with instructions provided by Ian at RC Tank Electronics and the receiver has been bound to the transmitter. What I can't fathom out is in the .ini file (a new one I've created from RC Tank Electronics), I've assigned channel 5 to be the front headlight. When I flick the switch on for channel 5 the light comes on but kills all functions. I can't get any movement from the tank whatsoever - turret rotation, elevation or wheels turning. If I switch the channel 5 switch back to off, all movement is restored. very odd. The headlight is soldered to the underside of the small 4 port daughter board.
Thirdly, the machine gun sounds, but no LED flashes. It is connected correctly to the small four port daughter board. Any ideas? i have ordered a replacement machine gun just in case the LED has blown.
Here are three piccies of the wiring on the daughterboard I've uploaded to Dropbox.
https://www.dropbox.com/sh/l8n1af1x9f6h ... 5ntTa?dl=0
Thanks in advance and apologies for being a pest.
A slight problem
-
- Lance Corporal
- Posts: 128
- Joined: Thu Jun 17, 2021 5:24 pm
A slight problem
‘Experience is the name everyone gives to their mistakes’ - Oscar Wilde
-
- Warrant Officer 1st Class
- Posts: 1664
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: A slight problem
![Wink ;)](./images/smilies/icon_e_wink.gif)
Question: did you check that it left the receiver doing what and with only the handle or button? because even if on the map it is indicated Ch.1 / 2/3. etc. this does not necessarily correspond to the outputs of the RX which may vary depending on the brand. To do this, you have to install a servomotor on each RX output and see who controls what? It also depends on the mode of your radio, mode 1 or 2 more common (see in the menu) and according to your piloting convenience. There can also be a mix (in triggered) or others on this channel, or bad programming? principle it is generally the right channel, can also see the program of the turntable? for the non-functional led? is it connected in the right way, and also not a problem with the program?
-
- Warrant Officer 1st Class
- Posts: 1664
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: A slight problem
here, who does what according to the type of transmitter mode (this for airplanes) in general it is mode 2 the most used
J
J
-
- Lance Corporal
- Posts: 128
- Joined: Thu Jun 17, 2021 5:24 pm
Re: A slight problem
The receiver is working fine. The switch I’ve got programmed is the one on the far left above the control knobs.Jofaur86 wrote:![]()
Question: did you check that it left the receiver doing what and with only the handle or button? because even if on the map it is indicated Ch.1 / 2/3. etc. this does not necessarily correspond to the outputs of the RX which may vary depending on the brand. To do this, you have to install a servomotor on each RX output and see who controls what? It also depends on the mode of your radio, mode 1 or 2 more common (see in the menu) and according to your piloting convenience. There can also be a mix (in triggered) or others on this channel, or bad programming? principle it is generally the right channel, can also see the program of the turntable? for the non-functional led? is it connected in the right way, and also not a problem with the program?
Switch works fine too, it’s just the light when it’s on kills everything apart from the engine running sound.
‘Experience is the name everyone gives to their mistakes’ - Oscar Wilde
-
- Warrant Officer 1st Class
- Posts: 1664
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: A slight problem
![:icon_e_surprised: :O](./images/smilies/icon_e_surprised.gif)
-
- Lance Corporal
- Posts: 128
- Joined: Thu Jun 17, 2021 5:24 pm
Re: A slight problem
I’ve not tried a different channel. I’ll give it a go tomorrow.Jofaur86 wrote:Sorry, can I mix the neurons ... for the trouble on channel 5? have you tried it on another channel?
‘Experience is the name everyone gives to their mistakes’ - Oscar Wilde
-
- Lance Corporal
- Posts: 128
- Joined: Thu Jun 17, 2021 5:24 pm
Re: A slight problem
I think I’ve got it sussed out.
Having had numerous emails flying back and forth to Ian at RC Tank Electronics, where I got the IBU board from, it looks as if the channel 5 connector on the board is faulty.
Ian say that he’ll have it back and test or replace it if needs be.
Having had numerous emails flying back and forth to Ian at RC Tank Electronics, where I got the IBU board from, it looks as if the channel 5 connector on the board is faulty.
Ian say that he’ll have it back and test or replace it if needs be.
‘Experience is the name everyone gives to their mistakes’ - Oscar Wilde
-
- Warrant Officer 1st Class
- Posts: 1664
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: A slight problem
HMikeHamilton wrote:I think I’ve got it sussed out.
Having had numerous emails flying back and forth to Ian at RC Tank Electronics, where I got the IBU board from, it looks as if the channel 5 connector on the board is faulty.
Ian say that he’ll have it back and test or replace it if needs be.
OK, hence the interest of trying with a servo
![Thumbup :thumbup:](./images/smilies/icon_thumbup.gif)
to confirm, the concern