IBU FO sound distortion
- leopardgreece
- Corporal
- Posts: 491
- Joined: Tue Oct 27, 2015 1:48 pm
IBU FO sound distortion
Hallo everybody. I have big problem with a new IBU2U FO 10 channel. When i start the Engine the sound of barrel up and down has real and obvious distortion. Can anyone help me with that???? Unfortunately I can't send here video to hear .Please help
????? ?? SM-N950F ???????????? Tapatalk
????? ?? SM-N950F ???????????? Tapatalk
Re: IBU FO sound distortion
Hello Leopardgreece,
Can you see what the endpoints are from the channel that is assigned to the barrel up/down. I think it is your left or right stick up/down (depending on mode1 or mode 2) that has a an end point of 100% and that should be around the 85%. I sit possible for you to show the endpoint values on your transmitter?
cheers Easy8
Can you see what the endpoints are from the channel that is assigned to the barrel up/down. I think it is your left or right stick up/down (depending on mode1 or mode 2) that has a an end point of 100% and that should be around the 85%. I sit possible for you to show the endpoint values on your transmitter?
cheers Easy8
- leopardgreece
- Corporal
- Posts: 491
- Joined: Tue Oct 27, 2015 1:48 pm
Re: IBU FO sound distortion
Yes sir ,i can ,i think that it was only 6 but i can see again today
????? ?? SM-N950F ???????????? Tapatalk
????? ?? SM-N950F ???????????? Tapatalk
- leopardgreece
- Corporal
- Posts: 491
- Joined: Tue Oct 27, 2015 1:48 pm
Re: IBU FO sound distortion
??.....6 was the file setup of the board and i changed it to 1 : barrelEngineOn.....
????? ?? SM-N950F ???????????? Tapatalk
????? ?? SM-N950F ???????????? Tapatalk
- leopardgreece
- Corporal
- Posts: 491
- Joined: Tue Oct 27, 2015 1:48 pm
Re: IBU FO sound distortion
Sir...Is that what u mean?
????? ?? SM-N950F ???????????? Tapatalk
????? ?? SM-N950F ???????????? Tapatalk
Re: IBU FO sound distortion
I see that channel 3 has a full 100% in the up and down position. I presume it is the channel for barrel up or down. Can you adjust the value from 100 to say 85 in both directions? Channel 10 is assigned to start up the engine ? Normally you can move your barrel up or down (with sound) without having your engine turned on. If you switch on the engine, while having the stick that operates your barrel in an up/downward position, you must realize that the loudspeaker has the full engine sound and the full elevation motor sound and that causes the the distortion. Therefore try to reduce the percentage of channel 3 to 85% or even less......
cheers Easy8
cheers Easy8
- leopardgreece
- Corporal
- Posts: 491
- Joined: Tue Oct 27, 2015 1:48 pm
Re: IBU FO sound distortion
?allo sir, how to do that ? Insert the microsd card into PC and charge something? I don't know exactly how to do that. Can you help a little bit ? Something like that?
????? ?? SM-N950F ???????????? Tapatalk
????? ?? SM-N950F ???????????? Tapatalk
- leopardgreece
- Corporal
- Posts: 491
- Joined: Tue Oct 27, 2015 1:48 pm
Re: IBU FO sound distortion
Also...Channel 10 is yes for start up the Engine as i can see at the radio transmitter photo
????? ?? SM-N950F ???????????? Tapatalk
????? ?? SM-N950F ???????????? Tapatalk
- leopardgreece
- Corporal
- Posts: 491
- Joined: Tue Oct 27, 2015 1:48 pm
Re: IBU FO sound distortion
I did that but didn't help. Also i change new speaker ....same problem
????? ?? SM-N950F ???????????? Tapatalk
????? ?? SM-N950F ???????????? Tapatalk