IBU2 help please
IBU2 help please
Hi.
Yesterday I tried to set up my IBU2 board, calibration went well , and then I couldnt figure out how to progress. I was tired so left it until today.
Start over, blue flashing light on board goes solid, remove the green jumper plug and then I get a message that says system fair check calibration eme file?
How do i do this ?
Thanks everyone.
Yesterday I tried to set up my IBU2 board, calibration went well , and then I couldnt figure out how to progress. I was tired so left it until today.
Start over, blue flashing light on board goes solid, remove the green jumper plug and then I get a message that says system fair check calibration eme file?
How do i do this ?
Thanks everyone.
- Model Builder 4
- 2nd Lieutenant
- Posts: 2329
- Joined: Sun Jul 26, 2015 3:46 pm
- Location: South Wales valleys
- Contact:
Re: IBU2 help please
Hi Will,
have a look on YouTube, Ian ( tankbear ) who is a member on here and runs rctankelectronics has done a walk through video for setting the ibu2 up, hope this helps
Cheers, Lee.
have a look on YouTube, Ian ( tankbear ) who is a member on here and runs rctankelectronics has done a walk through video for setting the ibu2 up, hope this helps
Cheers, Lee.
Me ? Addicted ? Never !!
- c.rainford73
- Major
- Posts: 6104
- Joined: Thu Aug 25, 2016 7:34 pm
- Location: Connecticut USA
Re: IBU2 help please
Just to clarify you remove the green jumper to only calibrate the board. So if calibration was completed the jumper should remain in place. The only time the board speaks to you to warn of low voltage if I'm correct or when you pull green jumper and calibration mode begins.essexbill wrote:Hi.
Yesterday I tried to set up my IBU2 board, calibration went well , and then I couldnt figure out how to progress. I was tired so left it until today.
Start over, blue flashing light on board goes solid, remove the green jumper plug and then I get a message that says system fair check calibration eme file?
How do i do this ?
Thanks everyone.
Is this green jumper plugged in after the calibration?
Tanks alot....
Re: IBU2 help please
Hi.
Yesterday I did the calibration , but other than guns nothing else worked, so I thought I would be able to start again today with a fresh calibration , but sadly all I am getting is the system fail message about an eme file
Yesterday I did the calibration , but other than guns nothing else worked, so I thought I would be able to start again today with a fresh calibration , but sadly all I am getting is the system fail message about an eme file
- midlife306
- Warrant Officer 1st Class
- Posts: 2238
- Joined: Sun Aug 27, 2017 10:34 am
Re: IBU2 help please
I fall for the nothing but the guns work bit, try turning the engine on lol..
I think it may be bottom right with the left joystick
Cheers
Wayne
Sent from my iPhone using Tapatalk
I think it may be bottom right with the left joystick
Cheers
Wayne
Sent from my iPhone using Tapatalk
- c.rainford73
- Major
- Posts: 6104
- Joined: Thu Aug 25, 2016 7:34 pm
- Location: Connecticut USA
Re: IBU2 help please
Bill did you go into the sd card provided and change any of the settings on the ini files? For instance I set my IBU2U boards so that engine start stop is channel 5. Did you alter the settings in any way?
Tanks alot....
Re: IBU2 help please
Hi Lee.Model Builder 4 wrote:Hi Will,
have a look on YouTube, Ian ( tankbear ) who is a member on here and runs rctankelectronics has done a walk through video for setting the ibu2 up, hope this helps
Cheers, Lee.
I have watched the video that shows you how to do the calibration, which is fine but as for all the settings I cannot find any helpful videos.
Re: IBU2 help please
Not changed any settings yet when I load the page on my laptop there are loads of values, people have said anything you change can easily be changed back but there's a hell of a lot there.c.rainford73 wrote:Bill did you go into the sd card provided and change any of the settings on the ini files? For instance I set my IBU2U boards so that engine start stop is channel 5. Did you alter the settings in any way?
Sadly I am old and and not very IT knowledgeable.
- c.rainford73
- Major
- Posts: 6104
- Joined: Thu Aug 25, 2016 7:34 pm
- Location: Connecticut USA
Re: IBU2 help please
Ok so you have completed the calibration process and the green jumper is reinstalled correct?
And then you recieve the error message?
Want to make sure I understand you Bill
And then you recieve the error message?
Want to make sure I understand you Bill
Tanks alot....
Re: IBU2 help please
I have figured out the error message and no longer have that.c.rainford73 wrote:Ok so you have completed the calibration process and the green jumper is reinstalled correct?
And then you recieve the error message?
Want to make sure I understand you Bill
All i have is left stick sonds stick up main gun stick down machine gun, left and right a traverse sound plus a general clanking sound which is probably tracks. When Iuse the stick the blue light on the board flashes.
Right stick theblue light flashes but no sounds or movements.