Torro Tiger 1 wiring
Forum rules
If your question is electronics related please post it in one of the relevant boards here: viewforum.php?f=31
If your question is electronics related please post it in one of the relevant boards here: viewforum.php?f=31
Torro Tiger 1 wiring
Hello
I need a bit of help, the wiring on my torro is different to my taigen Tiger 1, can you tell me what goes where on a taigen V3 please . when I put the plugs in ,the turret rotated but the main gun would not move or fire,also what are the wires for in pic 2.
Thanks in advance
Frank
I need a bit of help, the wiring on my torro is different to my taigen Tiger 1, can you tell me what goes where on a taigen V3 please . when I put the plugs in ,the turret rotated but the main gun would not move or fire,also what are the wires for in pic 2.
Thanks in advance
Frank
- Attachments
-
- terro 002.jpg (66.3 KiB) Viewed 717 times
-
- terro 001.jpg (73.18 KiB) Viewed 717 times
- 43rdRecceReg
- Major
- Posts: 6294
- Joined: Fri Jul 31, 2015 11:38 am
- Location: North West Highlands, Scotland
Re: Torro Tiger 1 wiring
It would help if you explain what you're trying to do. Are you trying to upgrade a Torro Tiger to a V3 Taigen setup, for example? It would also help if you showed the whole upper hull, and lower hull, wiring arrangements.
Generally, there's no obvious difference between Taigen and Torro, since they appear to be the same company. Did you not get a wiring diagram with the V3 unit? Like one of these, for instance:
https://www.taigentanks.com/collections ... rd-speaker.
One of the five-pin connectors will go in the IR port on the MFU. If you trace the wires (by colour) back to their points of origin (e.g. Gun microswitch, rotation unit, elevation unit etc.,), and then compare them with the designated slots on the V3 board (as per Taigen's instructions), you'll have a good idea of what goes where.
Here's somewhere to get the pdf for the Torro Tiger 1 (in German and English). It'll wise you up on the charging port at the rear, and more besides. There's also a connection guide. However, wiring is different on early
Taigen/Torro V1 and V2 Tigers, to that of the V3 models.
https://cdn.shopify.com/s/files/1/1052/ ... Manual.pdf
Generally, there's no obvious difference between Taigen and Torro, since they appear to be the same company. Did you not get a wiring diagram with the V3 unit? Like one of these, for instance:
https://www.taigentanks.com/collections ... rd-speaker.
One of the five-pin connectors will go in the IR port on the MFU. If you trace the wires (by colour) back to their points of origin (e.g. Gun microswitch, rotation unit, elevation unit etc.,), and then compare them with the designated slots on the V3 board (as per Taigen's instructions), you'll have a good idea of what goes where.
Here's somewhere to get the pdf for the Torro Tiger 1 (in German and English). It'll wise you up on the charging port at the rear, and more besides. There's also a connection guide. However, wiring is different on early
Taigen/Torro V1 and V2 Tigers, to that of the V3 models.
https://cdn.shopify.com/s/files/1/1052/ ... Manual.pdf
"Get your facts first, and then you can distort them as much as you please"- Mark Twain.
Re: Torro Tiger 1 wiring
Rotation and lights are likely hard soldered to the upper hull 8 pin PCB. The three pin connection on the upper hull PCB that I kinda see in the images is usually elevation and recoil/airsoft.
Re: Torro Tiger 1 wiring
The basic output functionconnections between V1 and V2 are the same.
See bottom of the above image for the upper hull pcb.
If you have the 3 pin connector reversed, you will have elevation but not recoil.See bottom of the above image for the upper hull pcb.
Re: Torro Tiger 1 wiring
Sorry. lotsa posts to answer. In image 2 you look to be trying to show the High Intensity Flash LED unit (Blurred in the image and above the two connectors.) That is usually stuffed down the gun barrel until that end is slightly visible from the side (or inside the muzzle brake if it has one.
Re: Torro Tiger 1 wiring
Hello
Thanks for all your replies, I bought a basket case with a lot of missing or broken parts. I have ordered Taigen Metal Suspension Arms, I used the V3 from my Taigen to test the Torro parts, the gear boxes are fine as is the turret rotation but there is damage and missing parts to the recoil unit. Can I buy a recoil unit ?
Thanks again
Frank
Thanks for all your replies, I bought a basket case with a lot of missing or broken parts. I have ordered Taigen Metal Suspension Arms, I used the V3 from my Taigen to test the Torro parts, the gear boxes are fine as is the turret rotation but there is damage and missing parts to the recoil unit. Can I buy a recoil unit ?
Thanks again
Frank
- Attachments
-
- tank parts 001.jpg (80.06 KiB) Viewed 680 times
-
- Warrant Officer 1st Class
- Posts: 1664
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: Torro Tiger 1 wiring
Hello, here is a picture of the wiring diagram between the board and the 8-pin socket, in principle the colors shown are those of the 8-wire cord, I don't know if you will help
https://www.forgebeartanks.com/store/c1 ... ducts.html
Asiatam Or this ?
the reversing unit is an Asiatam, and yes possible to buy, see herehttps://www.forgebeartanks.com/store/c1 ... ducts.html
Asiatam Or this ?
Re: Torro Tiger 1 wiring
Thats great thanks!!!
-
- Staff Sergeant
- Posts: 769
- Joined: Sat Oct 29, 2016 8:57 pm
- Location: Retford Nottinghamshire
-
- Staff Sergeant
- Posts: 769
- Joined: Sat Oct 29, 2016 8:57 pm
- Location: Retford Nottinghamshire