I am trying to fit lights and ir recievers into a Taigen late version metal turret cupola.
I can’t get it off to work on it, any ideas. The early version is a lot simpler.
Taigen late Tiger cupola removal
Forum rules
If your question is electronics related please post it in one of the relevant boards here: viewforum.php?f=31
If your question is electronics related please post it in one of the relevant boards here: viewforum.php?f=31
Taigen late Tiger cupola removal
Forced into tanks by a 9 year old.
Taigen tiger1 metal edition, 4:1 gearbox, mako2017,tiger ring
Torro King tiger, with ibu2u, fr7 and tarr ibu edition.
Tamiya Tiger 1 ElMod pro,tarr, twin speakers.
Taigen tiger1 metal edition, 4:1 gearbox, mako2017,tiger ring
Torro King tiger, with ibu2u, fr7 and tarr ibu edition.
Tamiya Tiger 1 ElMod pro,tarr, twin speakers.
-
- Lance Corporal
- Posts: 110
- Joined: Sat Apr 08, 2017 12:12 pm
- Location: Wallsend, Tyne & Wear
Re: Taigen late Tiger cupola removal
Just looked at my Taigen Panther and removal isn't obvious, all I can think of is applying heat, starting gently and working up.
I'm assuming it's just bonded in place, probably with hot melt glue or epoxy as opposed to anything fancy so heat may break the joint. I'd experiment a bit before stepping up to anything like a small gas torch, especially if there's any plastic inside the cupola.
Not very informed advice but may be an option before getting out the Dremel!
Dava.
I'm assuming it's just bonded in place, probably with hot melt glue or epoxy as opposed to anything fancy so heat may break the joint. I'd experiment a bit before stepping up to anything like a small gas torch, especially if there's any plastic inside the cupola.
Not very informed advice but may be an option before getting out the Dremel!
Dava.
Tamiya Tiger 1
Tamiya King Tiger
Tamiya/Wechoe Jagdtiger
Heng Long Stug iii
Heng Long Jagdpanther
Torro Jagdtiger
Taigen Panther G
Heng Long Challenger 2
Tamiya King Tiger
Tamiya/Wechoe Jagdtiger
Heng Long Stug iii
Heng Long Jagdpanther
Torro Jagdtiger
Taigen Panther G
Heng Long Challenger 2
Re: Taigen late Tiger cupola removal
Dava,
Thanks for that but i did try a heat gun with no obvious result.
I can see I can dremil out from underneath but didn't want to do it unless its last resort.
Thanks for that but i did try a heat gun with no obvious result.
I can see I can dremil out from underneath but didn't want to do it unless its last resort.
Forced into tanks by a 9 year old.
Taigen tiger1 metal edition, 4:1 gearbox, mako2017,tiger ring
Torro King tiger, with ibu2u, fr7 and tarr ibu edition.
Tamiya Tiger 1 ElMod pro,tarr, twin speakers.
Taigen tiger1 metal edition, 4:1 gearbox, mako2017,tiger ring
Torro King tiger, with ibu2u, fr7 and tarr ibu edition.
Tamiya Tiger 1 ElMod pro,tarr, twin speakers.
- silversurfer1947
- Lieutenant
- Posts: 3338
- Joined: Tue Oct 27, 2015 9:54 pm
- Location: Bristol, UK
Re: Taigen late Tiger cupola removal
Just a thought. Could it be super-glued in place? Have you tried a debonder?
Richard
Tamiya Tiger 1, Taigen FlakPanzer IV,Torro M16 half-track, Tamiya Panther,WSN/Torro T34,Taigen M41 Bulldog,H/l/Taigen Sherman M4A3,H/L T90, Haya M3 Grant, Metal Origins 234/2 Puma, Nashorn by Alwyn. I was only going to have one tank - honest!
Tamiya Tiger 1, Taigen FlakPanzer IV,Torro M16 half-track, Tamiya Panther,WSN/Torro T34,Taigen M41 Bulldog,H/l/Taigen Sherman M4A3,H/L T90, Haya M3 Grant, Metal Origins 234/2 Puma, Nashorn by Alwyn. I was only going to have one tank - honest!
-
- Lance Corporal
- Posts: 110
- Joined: Sat Apr 08, 2017 12:12 pm
- Location: Wallsend, Tyne & Wear
Re: Taigen late Tiger cupola removal
If you're just installing LEDs and ir receivers could you not build a module that could pop into place, possibly mounting them so that when at the right level, i.e the vision openings, you can push them outwards to fill the holes?
I'm thinking of something like holding your hand palm up, fingers together, pop in place and then open fingers outwards, make any sense? Like an upturned shuttlecock with the skirt cut into sections, each with an LED.
Far easier for me to say than do but you might expand this into a viable option.
Regards,Dava.
I'm thinking of something like holding your hand palm up, fingers together, pop in place and then open fingers outwards, make any sense? Like an upturned shuttlecock with the skirt cut into sections, each with an LED.
Far easier for me to say than do but you might expand this into a viable option.
Regards,Dava.
Tamiya Tiger 1
Tamiya King Tiger
Tamiya/Wechoe Jagdtiger
Heng Long Stug iii
Heng Long Jagdpanther
Torro Jagdtiger
Taigen Panther G
Heng Long Challenger 2
Tamiya King Tiger
Tamiya/Wechoe Jagdtiger
Heng Long Stug iii
Heng Long Jagdpanther
Torro Jagdtiger
Taigen Panther G
Heng Long Challenger 2
- silversurfer1947
- Lieutenant
- Posts: 3338
- Joined: Tue Oct 27, 2015 9:54 pm
- Location: Bristol, UK
Re: Taigen late Tiger cupola removal
If you want IR receptors and hit lights, have a look at rctanksaustralia.com who sell a unit specifically for a tiger.
Richard
Tamiya Tiger 1, Taigen FlakPanzer IV,Torro M16 half-track, Tamiya Panther,WSN/Torro T34,Taigen M41 Bulldog,H/l/Taigen Sherman M4A3,H/L T90, Haya M3 Grant, Metal Origins 234/2 Puma, Nashorn by Alwyn. I was only going to have one tank - honest!
Tamiya Tiger 1, Taigen FlakPanzer IV,Torro M16 half-track, Tamiya Panther,WSN/Torro T34,Taigen M41 Bulldog,H/l/Taigen Sherman M4A3,H/L T90, Haya M3 Grant, Metal Origins 234/2 Puma, Nashorn by Alwyn. I was only going to have one tank - honest!
Re: Taigen late Tiger cupola removal
Yes I bought a tiger ring from rc tank Australia. Just need to fit it nowsilversurfer1947 wrote:If you want IR receptors and hit lights, have a look at rctanksaustralia.com who sell a unit specifically for a tiger.
Forced into tanks by a 9 year old.
Taigen tiger1 metal edition, 4:1 gearbox, mako2017,tiger ring
Torro King tiger, with ibu2u, fr7 and tarr ibu edition.
Tamiya Tiger 1 ElMod pro,tarr, twin speakers.
Taigen tiger1 metal edition, 4:1 gearbox, mako2017,tiger ring
Torro King tiger, with ibu2u, fr7 and tarr ibu edition.
Tamiya Tiger 1 ElMod pro,tarr, twin speakers.