Help needed - WSN T-34 and Taigen 2.4GHz

Discuss your radio gear here!
Jofaur86
Warrant Officer 1st Class
Posts: 1663
Joined: Tue Dec 25, 2018 11:28 pm
Location: Centre France

Re: Help needed - WSN T-34 and Taigen 2.4GHz

Post by Jofaur86 »

schematic diagram heng long (old) general wiring, and the 8-pin plug of the upper chassis
B9A71D10-05ED-44FF-BFFC-C30C05AB3EF0.jpeg
B9A71D10-05ED-44FF-BFFC-C30C05AB3EF0.jpeg (58.54 KiB) Viewed 2756 times
SimonCornes
Lance Corporal
Posts: 189
Joined: Wed Jan 27, 2021 12:41 pm
Location: Stoke-on-Trent

Re: Help needed - WSN T-34 and Taigen 2.4GHz

Post by SimonCornes »

Thank you Jofaur86 - I will try to make sense of this!!
Simon
User avatar
wibblywobbly
Major
Posts: 6398
Joined: Fri Oct 17, 2008 9:30 am
Location: South Wales Valley
Contact:

Re: Help needed - WSN T-34 and Taigen 2.4GHz

Post by wibblywobbly »

Silversurfer is correct, my comms with the forum messages is very hit and miss.

It was many years ago that I converted a WSN T34 to an Elmod board. I took the route that was the easiest for me.

All tanks have two drive motors, a turret rotation motor, and an elevation motor. I simply cut all of the wires to each motor, installed new wiring to match an HL board as the Elmod used the same schematics.

I created a copy of the T34 that is at the Cobbaton museum.

phpBB [video]


phpBB [video]
Tiger 1 Late
Panther G
King Tiger
M36 B1
SimonCornes
Lance Corporal
Posts: 189
Joined: Wed Jan 27, 2021 12:41 pm
Location: Stoke-on-Trent

Re: Help needed - WSN T-34 and Taigen 2.4GHz

Post by SimonCornes »

Wibblywobbly, thank you very much for that. I will see what I can do to incorporate all of that!!

Simon
Jofaur86
Warrant Officer 1st Class
Posts: 1663
Joined: Tue Dec 25, 2018 11:28 pm
Location: Centre France

Re: Help needed - WSN T-34 and Taigen 2.4GHz

Post by Jofaur86 »

I agree with Wibblywobbly, just respect the wiring in order to correspond with the diagram with the colors indicated. :thumbup:
SimonCornes
Lance Corporal
Posts: 189
Joined: Wed Jan 27, 2021 12:41 pm
Location: Stoke-on-Trent

Re: Help needed - WSN T-34 and Taigen 2.4GHz

Post by SimonCornes »

Well guys, I had ago today with the standard wiring diagram and it didn't work! I have no idea why but when I reverted to the 8 pin arrangement in the Pan-Tiger which is fitted with an RX-18 MFU then it did what was expected. I've had to reverse the polarity of the wiring on the gun recoil motor so that works now but the LED in the tip of the barrel doesn't flash. I have a Taigen V3 in the tank so I hoped that I might get a 'bang' sound when the recoil works but no. In the WSN setup there is a red and black wire which goes to a small circuit board near to the speaker and that is no doubt how the 'bang' works but I have replaced that speaker - which didn't make a sound at all, even when running with the WSN radio - and also the associated board, with the Taigen one. As things stand the only thing missing now is the flashing Led and the main gun firing sound. Maybe that's as good as it will get. Certainly a damned sight better than the mad WSN system! I just need to sort out a 7.2v pack as this thing is not going to run on Duracells forever!

Simon
Jofaur86
Warrant Officer 1st Class
Posts: 1663
Joined: Tue Dec 25, 2018 11:28 pm
Location: Centre France

Re: Help needed - WSN T-34 and Taigen 2.4GHz

Post by Jofaur86 »

good evening, the gun led does not flash? possible plus / minus reversal if the original one? see on the recoil mechanism, must there be a small switch? it is he who controls the ignition, see also if correctly connected to RX 18, do you have this type of mechanism?
4268AAF0-7EF5-410A-93AE-F5E2D1F9E988.jpeg
4268AAF0-7EF5-410A-93AE-F5E2D1F9E988.jpeg (88.64 KiB) Viewed 2678 times
Jofaur86
Warrant Officer 1st Class
Posts: 1663
Joined: Tue Dec 25, 2018 11:28 pm
Location: Centre France

Re: Help needed - WSN T-34 and Taigen 2.4GHz

Post by Jofaur86 »

RX 18 2.4 ghz type connection, for the flash it is CN 3 (Xenon flash)
https://www.rc-panzershop.fr/ekmps/shop ... /hl2.4.pdf
old generation RX 18 diagram, but same as RX 2.4 ghz, on CN 3:
F: not used
G: more Led canon
H: less Led canon
J and K, switch on mechanism, recoil command, fire and flash. For information in case? the more on the led is the longer paw, hope will help
D3F9C5D3-3BCF-485E-9688-F4F9F1B3BDC5.jpeg
D3F9C5D3-3BCF-485E-9688-F4F9F1B3BDC5.jpeg (78.97 KiB) Viewed 2677 times
4366ECC7-46FE-457E-AD82-99A74AE4745D.jpeg
4366ECC7-46FE-457E-AD82-99A74AE4745D.jpeg (22.17 KiB) Viewed 2677 times
Désolée no perfect Langue :( traduction
Jofaur86
Warrant Officer 1st Class
Posts: 1663
Joined: Tue Dec 25, 2018 11:28 pm
Location: Centre France

Re: Help needed - WSN T-34 and Taigen 2.4GHz

Post by Jofaur86 »

found this on RC Universe? if can help
https://www.rcuniverse.com/forum/rc-tan ... r-3-a.html ???
john1970
Corporal
Posts: 372
Joined: Sun Jun 02, 2013 2:29 pm

Re: Help needed - WSN T-34 and Taigen 2.4GHz

Post by john1970 »

Microswitch if you dont have a microswitch fitted to the taigen board then you wont get the gun fire sound or if it is fitted and not being triggered you wont get gun fire sound
Post Reply

Return to “Radio Gear”