Hi mick,
case hardening powder was quite readily available in Australia. It was sold under the trade name of Hardite. As far as I know it was not deadly. But you made me curious and I will investigate further. Thank you.
Walter
Modifying Standard Gear Box
- Kostyanchik
- Private
- Posts: 63
- Joined: Wed Dec 13, 2017 3:37 pm
- Location: Russia, Moscow
Re: Modifying Standard Gear Box
Hello Walter!
on aliexpress can now purchase powerful motors. I thought maybe you would be interested.
With respect to you!
https://m.aliexpress.com/item/329445770 ... 2223871600
on aliexpress can now purchase powerful motors. I thought maybe you would be interested.
With respect to you!
https://m.aliexpress.com/item/329445770 ... 2223871600
- Attachments
-
- HTB1580gXpzsK1Rjy1Xbq6xOaFXaY.jpg_640x640q90.jpg (93.81 KiB) Viewed 4318 times
using translator
Re: Modifying Standard Gear Box
Hi Kostyanchik,
belatedly I thank you for bringing to my attention the new Johnson 395 10 grade rotor motor.
I still experiment with gear boxes. I find the motor plays a very important roll in the performance in a gear box.
Yesterday I ordered 2 Johnson 395 motors on the internet. I really look forward for their arrival.
Regards Walter
belatedly I thank you for bringing to my attention the new Johnson 395 10 grade rotor motor.
I still experiment with gear boxes. I find the motor plays a very important roll in the performance in a gear box.
Yesterday I ordered 2 Johnson 395 motors on the internet. I really look forward for their arrival.
Regards Walter
- Son of a gun-ner
- Lieutenant-Colonel
- Posts: 6925
- Joined: Sun May 07, 2017 8:49 pm
- Location: Surrey UK
Re: Modifying Standard Gear Box
Do these Johnson 395 motors have the same shaft diameter and two screw fixing holes in the same place as the Heng Long motors?
Therefore, can they be used as a direct swap for the Heng Long motors?
Mick.
Therefore, can they be used as a direct swap for the Heng Long motors?
Mick.
Mick - The grit in the underpants of life!
And always happy to spare the bytes
TOTM needs YOU support YOUR TOTM competition, I'm doing my part, are YOU?
And always happy to spare the bytes
TOTM needs YOU support YOUR TOTM competition, I'm doing my part, are YOU?
- wibblywobbly
- Major
- Posts: 6398
- Joined: Fri Oct 17, 2008 9:30 am
- Location: South Wales Valley
- Contact:
Re: Modifying Standard Gear Box
Motor diameter : 27.6mmSon of a gun-ner wrote:Do these Johnson 395 motors have the same shaft diameter and two screw fixing holes in the same place as the Heng Long motors?
Therefore, can they be used as a direct swap for the Heng Long motors?
Mick.
Motor length : 46.5mm
Shaft diameter : 2.3mm
Shaft length : 13mm
Screw holes : M 2.5
Mounting holes distance : 16 MM
They seem to be 390 motors so same as HL but longer casings? If they are longer, I haven't measured an HL one, then they may not fit. Worth getting a ruler out for though.
Tiger 1 Late
Panther G
King Tiger
M36 B1
Panther G
King Tiger
M36 B1
- Son of a gun-ner
- Lieutenant-Colonel
- Posts: 6925
- Joined: Sun May 07, 2017 8:49 pm
- Location: Surrey UK
Re: Modifying Standard Gear Box
Thanks Rob
I very much like the number of poles these motors have, means better low speed control.
I very much like the number of poles these motors have, means better low speed control.
Mick - The grit in the underpants of life!
And always happy to spare the bytes
TOTM needs YOU support YOUR TOTM competition, I'm doing my part, are YOU?
And always happy to spare the bytes
TOTM needs YOU support YOUR TOTM competition, I'm doing my part, are YOU?
- Kostyanchik
- Private
- Posts: 63
- Joined: Wed Dec 13, 2017 3:37 pm
- Location: Russia, Moscow
Re: Modifying Standard Gear Box
These motors correspond in their dimensions to the R390 and speed 480 motors.
Compared with the standard HengLong motors, these motor shells are approximately 10 mm longer.
Compared with the standard HengLong motors, these motor shells are approximately 10 mm longer.
using translator