Maybe Lee.....maybe....Model Builder 4 wrote:Very nice Rob you must have been extremely good this year to receive such great presents
Cheers, Lee.
X-Mas came early this year
Re: X-Mas came early this year
Re: X-Mas came early this year
Tonight I wanted to charge both batteries, so I could make a test ride tomorrow morning.
F*ck.....in the box from the F type, no charger.
Yesterday afternoon I only un-boxed both tanks, to check them out, and did not look any further if the box was complete.
I bought both Panthers from Dominique at RCTank.de, so I emaild him about it.
I felt a bit stupid, telling him the day after the delivery that one loader is missing....damn.
On here he often is mentioned as a good vendor, so maybe he will send me another charger.
To check if everything was working on both Panthers, I took the Tiger's battery pack and put it from Panther to Panther.
Fortunately everything on the newbies just worked fine.
To be continued guys....
F*ck.....in the box from the F type, no charger.
Yesterday afternoon I only un-boxed both tanks, to check them out, and did not look any further if the box was complete.
I bought both Panthers from Dominique at RCTank.de, so I emaild him about it.
I felt a bit stupid, telling him the day after the delivery that one loader is missing....damn.
On here he often is mentioned as a good vendor, so maybe he will send me another charger.
To check if everything was working on both Panthers, I took the Tiger's battery pack and put it from Panther to Panther.
Fortunately everything on the newbies just worked fine.
To be continued guys....
Re: X-Mas came early this year
Due to holidays from the German antenna supplier, my stuff will come in somewhere half of August.
So I just have to be a little patient.
So I just have to be a little patient.
Re: X-Mas came early this year
A few minutes ago I received an email from Dominique (RCTank.de)
He felt sorry the charger was not in the box, and a new one will be shipped later today.
What a great guy, I can highly recommend him and his site.
Because I did not notice the missing charger at first, found out a day later, he could have said it was my fault and I should have checked it from day 1.
Nothing about that, just sends a new one.
Just GREAT.
He felt sorry the charger was not in the box, and a new one will be shipped later today.
What a great guy, I can highly recommend him and his site.
Because I did not notice the missing charger at first, found out a day later, he could have said it was my fault and I should have checked it from day 1.
Nothing about that, just sends a new one.
Just GREAT.
- General Jumbo01
- Warrant Officer 1st Class
- Posts: 1763
- Joined: Sat Jul 14, 2018 8:06 pm
- Location: I'm a Londoner that moved to Essex. Says it all really...:(
Re: X-Mas came early this year
I too used plasticity which is easy to cut and add the small fixings. To the back of the card l glued small brass plates and to those l soldered thin brass tube. I then drill 3 small holes into the hull just below the edge of the hull wheel cover plate (sorry, don't know the correct term) and glues into the holes short tubes to take the rods.
In this way you can run the Panther without the side plates with no visible fixing plates or by simply sliding the plate's rods into the tubes, you can run with the plates. Well, it works for me - and if preferred you could use the same method but use aluminium or brass.
Btw, both tracks look pretty good to me, not too tight for a just out of the factory or too slack for a low mileage job!
In this way you can run the Panther without the side plates with no visible fixing plates or by simply sliding the plate's rods into the tubes, you can run with the plates. Well, it works for me - and if preferred you could use the same method but use aluminium or brass.
Btw, both tracks look pretty good to me, not too tight for a just out of the factory or too slack for a low mileage job!
Owner - Fuckleburgh Tank Collection
- General Jumbo01
- Warrant Officer 1st Class
- Posts: 1763
- Joined: Sat Jul 14, 2018 8:06 pm
- Location: I'm a Londoner that moved to Essex. Says it all really...:(
Re: X-Mas came early this year
And with plates fitted, you can't see the top run of the track anyway!
Owner - Fuckleburgh Tank Collection
- General Jumbo01
- Warrant Officer 1st Class
- Posts: 1763
- Joined: Sat Jul 14, 2018 8:06 pm
- Location: I'm a Londoner that moved to Essex. Says it all really...:(
Re: X-Mas came early this year
The first shot shows one of the mounting plates in position, the rod just slid into the tube, and the second shot shows the finished set in position. You really need to make the separate plates, either by fabricating the separately or by scoring the platicard and then add the tiny fixing buckles. Also, be aware that the number, and therefore the lengths of the individual plates varied over time.
That new model F looks great by the way. Must add it to my Xmas list - note to Dave at Forgebear, Don't let that IS-2 slip any futher or my Xmas list will be full already
Sent from my ASUS_T00G using Tapatalk
That new model F looks great by the way. Must add it to my Xmas list - note to Dave at Forgebear, Don't let that IS-2 slip any futher or my Xmas list will be full already
Sent from my ASUS_T00G using Tapatalk
Owner - Fuckleburgh Tank Collection
Re: X-Mas came early this year
Yes that is correctGeneral Jumbo01 wrote:And with plates fitted, you can't see the top run of the track anyway!
Re: X-Mas came early this year
Thanks General for the info and pics.
At work looking at it on my phone.
Will check on it all back home on the pc.
Maybe I will contact you again about the Schürzen, if it is okay with you.
Must re-read it some more times to understand what exactly you did.
At work looking at it on my phone.
Will check on it all back home on the pc.
Maybe I will contact you again about the Schürzen, if it is okay with you.
Must re-read it some more times to understand what exactly you did.