Jagtiger in need of a reboot
Re: Jagtiger in need of a reboot
OK, we seem to have established that I don't have a scooby about what I'm doing.
Big question, is it possible for me to rewire the tank using the diagrams already provided and the tk 7.0 connection schematic?
If so, silly 1st question - what connectors do I need to buy?
Big question, is it possible for me to rewire the tank using the diagrams already provided and the tk 7.0 connection schematic?
If so, silly 1st question - what connectors do I need to buy?
- Herr Dr. Professor
- Lieutenant
- Posts: 3835
- Joined: Mon Apr 22, 2019 10:48 pm
- Location: Southern Wisconsin USA
Re: Jagtiger in need of a reboot
Hwal2605: I have been reading all along, but have been silent because I am unfamiliar with the HengLong 7.0 and its significant differences from earlier HengLong boards. I just want to encourage you not to give up. Consider this, I have smoked more electronics than I ever smoked a cigarette (however---well, that's another thing from my college days). I just chuckle, get slivers under my fingernails, and start over.
- jarndice
- Colonel
- Posts: 8042
- Joined: Mon Sep 03, 2012 11:27 am
- Location: the mountains of hertfordshire
Re: Jagtiger in need of a reboot
I am afraid I am going to be very negative, The Heng Long 7.0 board is a very nice piece of kit but retrofitting it into an earlier Heng Long wired Tank is going to be a nightmare,
It will mean a total rewiring including new plugs on every connector,If you are going to do that for goodness sake label every wire first so that you will know what goes where.(A Tip, A wrap of masking tape round the wire with a number on it, Using a notebook write what that number on the wire is for, such as 7= drive motor POS, or 4= Turret motor Neg etc.
And don't forget you will need a 7.0 board wiring diagram and instructions.
Before the 7.0 board each update was a simple moving around of plugs in sockets and swapping from a Heng Long Control board to a Taigen board was just a swapping of plugs but now even the plugs have been changed. The obvious choice is either a Taigen V2/3 board + Taigen V2/3 Transmitter(Plug and Play, cheap but a backwards step compared to the 7.0 board) or an aftermarket board and transmitter/receiver where you can at least use the existing plugs,
More money but a far better r/c Tank will be the result.
Sorry but this is the easiest way I know of spending large sums of money usually closely followed by much in the way of regret
It will mean a total rewiring including new plugs on every connector,If you are going to do that for goodness sake label every wire first so that you will know what goes where.(A Tip, A wrap of masking tape round the wire with a number on it, Using a notebook write what that number on the wire is for, such as 7= drive motor POS, or 4= Turret motor Neg etc.
And don't forget you will need a 7.0 board wiring diagram and instructions.
Before the 7.0 board each update was a simple moving around of plugs in sockets and swapping from a Heng Long Control board to a Taigen board was just a swapping of plugs but now even the plugs have been changed. The obvious choice is either a Taigen V2/3 board + Taigen V2/3 Transmitter(Plug and Play, cheap but a backwards step compared to the 7.0 board) or an aftermarket board and transmitter/receiver where you can at least use the existing plugs,
More money but a far better r/c Tank will be the result.
Sorry but this is the easiest way I know of spending large sums of money usually closely followed by much in the way of regret
I think I am about to upset someone
-
- Warrant Officer 1st Class
- Posts: 1680
- Joined: Tue Dec 25, 2018 11:28 pm
- Location: Centre France
Re: Jagtiger in need of a reboot
Hello, as indicated in a previous message, and I join Jarndice, it is certain that it will be a hell of a job, but nothing is impossible? except as mentioned above, risk of costing an arm! Do you already have a Tiger I Taigen? so a plate identical to that of the Jagdtiger, and the transmitter that goes with it? (the Heng Long don't have fans..) why don't you already use this transmitter? by binding the plate, of course, to see if it works? because without wanting to offend you!!! it seems to me that there is not great wiring, so check well against the attached photos that correspond well. And will already allow you to have an idea.
Re: Jagtiger in need of a reboot
Thanks to all for their comments.
It seems I have two options.
1. Proceed with 7.0 and rewire the tank.
2. Look to find a Taigen v3 transmitter (of use my existing one - not great long term as this tank is going to a friend).
Can someone point me to the Taigen "bind" process so I can at least see if that works.
It seems I have two options.
1. Proceed with 7.0 and rewire the tank.
2. Look to find a Taigen v3 transmitter (of use my existing one - not great long term as this tank is going to a friend).
Can someone point me to the Taigen "bind" process so I can at least see if that works.
- HERMAN BIX
- Brigadier
- Posts: 10411
- Joined: Sun Jan 12, 2014 12:15 am
- Location: Gold Coast,Australia
Re: Jagtiger in need of a reboot
https://www.youtube.com/watch?v=e-ddQjBcPCY
Try this
But, store the H/L V7 unit.Thats my angle .
Get a Taigen V3 unit, with sound board................................they are cheap, and work.
Getting another board into a tank that has been sorted to work with one or another can be a headache
Try this
But, store the H/L V7 unit.Thats my angle .
Get a Taigen V3 unit, with sound board................................they are cheap, and work.
Getting another board into a tank that has been sorted to work with one or another can be a headache
HL JAGDPANTHER,HL TIGER 1,HL PzIII MUNITIONSCHLEPPER, HL KT OCTOPUS,HL PANTHER ZU-FUSS,HL STuG III,HL T34/85 BEDSPRING,
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
HL PZIV MALTA,MATORRO JAGDTIGER,HL F05 TIGER,TAMIYA KT,HL PANTHERDOZER,HL EARLY PANTHER G,TAIGEN/RAMINATOR T34/76,
HL AN-BRI-RAM SU-85
- Herr Dr. Professor
- Lieutenant
- Posts: 3835
- Joined: Mon Apr 22, 2019 10:48 pm
- Location: Southern Wisconsin USA
Re: Jagtiger in need of a reboot
I second Bix's recommendation. However, if your friend doesn't need Taigen V3 sound, PM me. I have been pulling out older Taigen boards to put in V3 electronics, so I have perfectly good older boards around.
Re: Jagtiger in need of a reboot
What ever board you use be careful as your upper hull will need rewiring if you look at the picture or on the tank the 8 pin connector on the upper hull is a rewired 10 pin connector and the wiring has been altered so things aren't wired as the would have been on the taigen board also your BB gun doesn't have a microswitch on the back of it so you wont get gun fire sound.
Re: Jagtiger in need of a reboot
Thanks John1970, I'll need some help with that. What's the spec of the 2 pin and other plugs, as I'll need to buy a few of them.
Re: Jagtiger in need of a reboot
JST connector 2.54 pitch
Dupont connector 2 pin 2.54 pitch for LED's
Dupont connector 2 pin 2.54 pitch for LED's