I'd like to start a Clark board info page.
-
- Lance Corporal
- Posts: 137
- Joined: Sat Oct 03, 2020 4:34 am
I'd like to start a Clark board info page.
OK so the holy grail pages http://www.clark-model.com/eng/index_e.html
Some TK40 info https://www.youtube.com/watch?app=desktop&v=K5bJ4hcaEJI
Feel free to add what you know as well.
If a moderator could put the pictures to the relevant wording that would be grouse .
Some TK40 info https://www.youtube.com/watch?app=desktop&v=K5bJ4hcaEJI
Feel free to add what you know as well.
If a moderator could put the pictures to the relevant wording that would be grouse .
- Attachments
-
- FS-i6s_10-300x158.jpg (15.14 KiB) Viewed 2353 times
-
- KX9nLUi.jpg (44.67 KiB) Viewed 2356 times
Last edited by Biasphere1 on Sun Aug 07, 2022 6:53 am, edited 3 times in total.
-
- Lance Corporal
- Posts: 137
- Joined: Sat Oct 03, 2020 4:34 am
Re: I'd like to start a Clark board info page.
How to Setup FlySky i6s Radio with a Clark SBUS TK Board
Plug the FlySky FS-iA10B or FS-iA6B receiver wire from the TK board into the receivers port labeled as SERVO.
NOTE – This will apply only to CH1 of the TK40/TK50 series board if there are multiple receiver leads. Other receiver leads will not be connected in this scenario.
NOTE – There will be only only receiver lead from the TK board for TK60/TK80 series boards.
Make sure the receiver wire is plugged in correctly.
NOTE – The metal contacts will face outwards and the wires will generally be colored from left to right – black, red, white.
On the FlySky i6s radio, tap on the Settings icon.
Tap on the System menu tab
Tap on the Output Mode menu tab, then tap on both PWM and S.BUS.
PIcture at foot of page .
Tap on the Function menu tab, then tap on the Aux. channels option.
Tap on channels 5-10 and assign as follows:
NOTE: Channel 9 is your main cannon and MG1. Swap the channel mapping, with CH9 to VrA and CH10 to VrB to map main canon to VrA.
To set your drive stick as the RIGHT stick – under the System menu, go to Sticks mode, and set as M2
To set your drive stick as the LEFT stick – under the System menu, go to Sticks mode, and set as M3Tap on the Function menu tab, then tap on the Aux. channels option.
Tap on channels 5-10 and assign as follows:
NOTE: Channel 9 is your main cannon and MG1. Swap the channel mapping, with CH9 to VrA and CH10 to VrB to map main canon to VrA.
To set your drive stick as the RIGHT stick – under the System menu, go to Sticks mode, and set as M2
To set your drive stick as the LEFT stick – under the System menu, go to Sticks mode, and set as M3
Plug the FlySky FS-iA10B or FS-iA6B receiver wire from the TK board into the receivers port labeled as SERVO.
NOTE – This will apply only to CH1 of the TK40/TK50 series board if there are multiple receiver leads. Other receiver leads will not be connected in this scenario.
NOTE – There will be only only receiver lead from the TK board for TK60/TK80 series boards.
Make sure the receiver wire is plugged in correctly.
NOTE – The metal contacts will face outwards and the wires will generally be colored from left to right – black, red, white.
On the FlySky i6s radio, tap on the Settings icon.
Tap on the System menu tab
Tap on the Output Mode menu tab, then tap on both PWM and S.BUS.
PIcture at foot of page .
Tap on the Function menu tab, then tap on the Aux. channels option.
Tap on channels 5-10 and assign as follows:
NOTE: Channel 9 is your main cannon and MG1. Swap the channel mapping, with CH9 to VrA and CH10 to VrB to map main canon to VrA.
To set your drive stick as the RIGHT stick – under the System menu, go to Sticks mode, and set as M2
To set your drive stick as the LEFT stick – under the System menu, go to Sticks mode, and set as M3Tap on the Function menu tab, then tap on the Aux. channels option.
Tap on channels 5-10 and assign as follows:
NOTE: Channel 9 is your main cannon and MG1. Swap the channel mapping, with CH9 to VrA and CH10 to VrB to map main canon to VrA.
To set your drive stick as the RIGHT stick – under the System menu, go to Sticks mode, and set as M2
To set your drive stick as the LEFT stick – under the System menu, go to Sticks mode, and set as M3
-
- Lance Corporal
- Posts: 137
- Joined: Sat Oct 03, 2020 4:34 am
Re: I'd like to start a Clark board info page.
TK24S dedicated page .
S.BUS setup ( FlySky i6S )
Transmitter:
1.Turn on Transmitter i6s and enter setting function, go to system->output mode, than set Serial to S.BUS
2. Enter aux channel setup, set channel 5 to SwA, channel 6 to SwD, channel 7 to SwB, channel 8 to SwC, channel 9 to VrA and channel 10 to VrB,
3. Go to system->stick mode, then set to M1 mode,
4. Go to end points page, set end point to 100% for every channel.
Receiver and control board:
1. Plug connector with S.BUS label on it into S.BUS port on receiver.
S.BUS setup ( FlySky i6S )
Transmitter:
1.Turn on Transmitter i6s and enter setting function, go to system->output mode, than set Serial to S.BUS
2. Enter aux channel setup, set channel 5 to SwA, channel 6 to SwD, channel 7 to SwB, channel 8 to SwC, channel 9 to VrA and channel 10 to VrB,
3. Go to system->stick mode, then set to M1 mode,
4. Go to end points page, set end point to 100% for every channel.
Receiver and control board:
1. Plug connector with S.BUS label on it into S.BUS port on receiver.
- Attachments
-
- sbus menu.jpg (48.89 KiB) Viewed 2352 times
Re: I'd like to start a Clark board info page.
Drammen Rock City
- c.rainford73
- Major
- Posts: 6104
- Joined: Thu Aug 25, 2016 7:34 pm
- Location: Connecticut USA
-
- Lance Corporal
- Posts: 137
- Joined: Sat Oct 03, 2020 4:34 am
Re: I'd like to start a Clark board info page.
If any of you fine people have Clark board ,know a youtube instructional video or have Sony programmer instruction PDF's feel free to post up here please .
My Sony remote and configuration kit from Kenny at DAKRCTANK is on it's way , so I might be able to post up if it comes with instructions. I sorta hope it does .lol
Cheers .
My Sony remote and configuration kit from Kenny at DAKRCTANK is on it's way , so I might be able to post up if it comes with instructions. I sorta hope it does .lol
Cheers .
- Markocaster
- Staff Sergeant
- Posts: 991
- Joined: Mon Mar 31, 2014 11:16 pm
- Location: Bay Area , California
Re: I'd like to start a Clark board info page.
Super helpful post. Cheers
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
HL /Mato tiger 1 early, Tamiya Tiger 1 early, Taigen tiger 1 mid
Taigen T34/85, HL SU-100
Jagdpanzer Lang
Taiga Jagdpanther
Heng Long Sherman DGS Firefly kit
Tamiya King Tiger (unbuilt)
Mato all metal Panzer III
1/10 Jagdpanther
Taigen T34/85, HL SU-100
Jagdpanzer Lang
Taiga Jagdpanther
Heng Long Sherman DGS Firefly kit
Tamiya King Tiger (unbuilt)
Mato all metal Panzer III
1/10 Jagdpanther
-
- Lance Corporal
- Posts: 137
- Joined: Sat Oct 03, 2020 4:34 am
-
- Lance Corporal
- Posts: 137
- Joined: Sat Oct 03, 2020 4:34 am
Re: I'd like to start a Clark board info page.
TBA problems lol.